Green Solvents, Energy Sources and Industrial Case Studies
CSIR NET green chemistry: water, supercritical CO₂, ionic liquids, solvent-free and microwave methods, renewable feedstocks, safer reagents, case studies.
- 20 min
On this page · 17 sections
- Prerequisites
- The Hook: The Solvent Is Most of the Flask
- 1. Choosing a Solvent
- 2. Water
- 3. Supercritical Fluids
- 4. Ionic Liquids and Deep Eutectic Solvents
- 5. Alternative Energy Input
- 6. Renewable Feedstocks
- 7. Safer Reagents and Inherently Safer Design
- 8. Industrial Case Studies
- Memory Tricks
- Don’t Confuse
- Common Mistakes
- Practice
- Quick Revision Table
- Key Takeaways
- What’s Next
Prerequisites
- Green Chemistry: The Twelve Principles and Metrics: this page applies principles 3, 5, 6, 7, 10 and 12 and uses atom economy and E-factor throughout.
- Phase Equilibria and the Phase Rule: critical points and phase diagrams behind supercritical fluids.
- Non-Aqueous Solvents: how solvent properties control reactivity, the background to ionic liquids.
- Catalysis Across Chemistry: phase-transfer catalysis and biocatalysis reappear here as green tools.
The Hook: The Solvent Is Most of the Flask
1. Choosing a Solvent
What makes a solvent green
- low toxicity and no carcinogenicity, mutagenicity or reproductive toxicity
- low volatility or easy containment, high flash point
- not ozone-depleting, low global-warming impact
- biodegradable, derived from renewable sources where possible
- easy to recover and recycle, with modest energy for distillation
Pharmaceutical companies and academic consortia publish solvent selection guides that rank solvents broadly as preferred, usable or undesirable. The rankings differ in detail, but the pattern is consistent:
| Generally preferred | Usable with care | Generally avoided, with common replacements |
|---|---|---|
| water, ethanol, 2-propanol, 1-butanol, ethyl acetate, isopropyl acetate, acetone | toluene, heptane, acetonitrile, methyl tert-butyl ether, 2-methyltetrahydrofuran, DMSO | benzene (→ toluene); CCl₄ and chloroform (→ dichloromethane at worst, better ethyl acetate or 2-MeTHF); diethyl ether (→ 2-MeTHF or MTBE); hexane (→ heptane); DMF, NMP, DMAc (→ DMSO or bio-based dipolar aprotics); 1,4-dioxane (→ 2-MeTHF) |
Hexane is replaced by heptane because hexane is metabolised to a neurotoxic diketone; heptane is not. 2-Methyltetrahydrofuran can be made from furfural, a biomass-derived chemical, and separates cleanly from water, which THF does not.
The best solvent is no solvent
Solvent-free reactions avoid the problem entirely: neat liquid reagents, melts, or solids ground together. Mechanochemistry uses mechanical energy (mortar and pestle, ball mills) to drive reactions between solids. Condensations (aldol, Knoevenagel), imine formation, some cross-couplings and many co-crystal and metal–organic framework preparations work this way, often faster and with simpler work-up.
2. Water
Water is non-toxic, non-flammable, cheap and abundant. Its drawbacks are poor solubility of many organic compounds, reactivity towards water-sensitive reagents, and the energy cost of removing it or of treating contaminated aqueous waste.
Water can also accelerate reactions. The Diels–Alder reaction of cyclopentadiene with a dienophile such as methyl vinyl ketone is markedly faster in water than in hydrocarbon solvents. Two effects are invoked:
- the hydrophobic effect: water pushes the non-polar reactants together, and the more compact transition state exposes less hydrophobic surface;
- hydrogen bonding from water to the carbonyl of the dienophile, which stabilises the polarised transition state (a Lewis-acid-like effect).
Reactions of insoluble organics stirred as a suspension on water (“on water”) and reactions inside surfactant micelles in water (micellar catalysis) extend this approach to many metal-catalysed couplings.
3. Supercritical Fluids
Above its critical temperature \( T_c \) and critical pressure \( P_c \), a substance has no distinct liquid and gas phases: it is a supercritical fluid (SCF). SCFs combine liquid-like density (and therefore solvating power) with gas-like viscosity and diffusivity. Near the critical point, density, and with it solvent strength, changes steeply with small changes in pressure or temperature, so the solvent can be tuned, and solutes can be precipitated simply by releasing pressure.
| Fluid | \( T_c \) | \( P_c \) | Key uses |
|---|---|---|---|
| CO₂ | 31.1 °C (304.1 K) | 73.8 bar (7.38 MPa) | decaffeination of coffee, extraction of flavours and hops, dry cleaning, hydrogenation, polymer processing, chromatography (SFC) |
| H₂O | about 374 °C | about 22.1 MPa | supercritical water oxidation of hazardous waste; near-critical water as a reaction medium |
Supercritical CO₂ (scCO₂)
| Advantage | Limitation |
|---|---|
| low, accessible critical temperature (good for heat-sensitive natural products) | needs pressure equipment |
| non-toxic, non-flammable, cheap; recovered from other processes | non-polar: poor solvent for polar and ionic compounds (add a co-solvent such as methanol or ethanol, or a CO₂-philic surfactant) |
| completely miscible with H₂ and O₂: no gas–liquid mass-transfer limit in hydrogenations and oxidations | reacts with strong nucleophiles such as primary amines (carbamate formation) |
| no solvent residue: depressurising leaves solvent-free product | CO₂ is a greenhouse gas, though the CO₂ used is captured, not newly produced |
Supercritical water
As water is heated towards its critical point its hydrogen-bond network breaks down and its dielectric constant falls sharply, so supercritical water behaves like a non-polar organic solvent: it dissolves organic compounds and O₂ completely and dissolves inorganic salts poorly. Organic waste oxidised in supercritical water is converted to CO₂ and water in a single homogeneous phase; salts precipitate.
4. Ionic Liquids and Deep Eutectic Solvents
Ionic liquids (ILs)
An ionic liquid is a salt that melts below 100 °C; room-temperature ionic liquids are liquid at ambient temperature. They are built from bulky, asymmetric organic cations and weakly coordinating anions, which frustrate crystal packing.
| Component | Common examples |
|---|---|
| Cations | 1-alkyl-3-methylimidazolium ([BMIM]⁺ = 1-butyl-3-methylimidazolium), N-alkylpyridinium, tetraalkylammonium, tetraalkylphosphonium |
| Anions | Cl⁻, Br⁻, BF₄⁻, PF₆⁻, bis(trifluoromethylsulfonyl)imide (NTf₂⁻), triflate, acetate, alkyl sulfates |
Properties that make them attractive:
- negligible vapour pressure: no volatile emissions, products can be distilled out
- generally non-flammable, thermally stable, wide liquid range
- tunable: changing the cation chain length or anion changes polarity, water miscibility and viscosity (“designer solvents”); hydrophobic ILs ([BMIM][PF₆], [BMIM][NTf₂]) form a separate phase with water, while [BMIM][BF₄] and [BMIM]Cl are water-miscible
- dissolve many metal catalysts, which stay in the IL phase for reuse; some (chloride and acetate ILs) dissolve cellulose
- can serve as electrolytes with wide electrochemical windows
Why they are not automatically green:
- some are toxic to aquatic organisms and poorly biodegradable
- expensive, and synthesis (alkylation, anion metathesis) generates its own waste
- PF₆⁻ and BF₄⁻ can hydrolyse in wet, hot conditions, releasing HF
- high viscosity slows mass transfer; purification of products and recycling of the IL take effort
Deep eutectic solvents (DES)
A deep eutectic solvent is a mixture of a hydrogen-bond acceptor (often a quaternary ammonium salt such as choline chloride) and a hydrogen-bond donor (urea, glycerol, carboxylic acids) whose eutectic melting point lies far below those of the components. The standard example is choline chloride and urea in a 1 : 2 molar ratio, which is liquid near room temperature although both components are high-melting solids. DESs share many IL properties (low volatility, tunability) but are cheap, made simply by mixing (100% atom economy, no purification), and often built from biodegradable, low-toxicity components.
Other alternative media
| Medium | Point to remember |
|---|---|
| Polyethylene glycol (PEG) | non-volatile, low toxicity, water-soluble; recyclable reaction medium |
| Fluorous solvents (perfluoroalkanes) | immiscible with water and many organic solvents at room temperature; fluorous-tagged catalysts are separated in a fluorous phase (fluorous biphasic catalysis) |
| Bio-based solvents | ethanol, ethyl lactate, 2-MeTHF, limonene, glycerol |
5. Alternative Energy Input
Microwave heating
Laboratory and domestic microwave reactors operate at 2.45 GHz (wavelength \( c/f = 3.00\times10^8/2.45\times10^9 = 0.122 \) m, about 12 cm). Microwaves heat by:
- dipolar polarisation: permanent dipoles try to follow the oscillating field; the lag converts field energy into heat;
- ionic conduction: dissolved ions oscillate and collide.
How well a solvent absorbs is measured by the loss tangent \( \tan\delta = \varepsilon''/\varepsilon' \) (dielectric loss over dielectric constant). Polar, high-loss solvents (ethylene glycol, ethanol, DMSO) heat very rapidly; non-polar solvents (hexane, toluene, CCl₄) are nearly transparent and barely heat unless a polar reagent, ionic liquid or absorbing vessel is present.
Benefits: volumetric “in-core” heating without hot vessel walls, fast ramp to temperature, easy superheating above the normal boiling point in sealed vessels, and reaction times cut from hours to minutes, often with cleaner product profiles. Most rate increases are explained by the higher temperatures reached (thermal effects); claims of special non-thermal microwave effects remain contested.
Ultrasound (sonochemistry)
Ultrasound (frequencies above human hearing, from 20 kHz upwards) acts through acoustic cavitation: the formation, growth and violent collapse of microbubbles in a liquid. Collapse creates local hot spots of extremely high temperature and pressure for very short times, plus shock waves and microjets. Effects: radical formation from solvent (sonolysis), cleaning and activation of metal surfaces (Grignard and Barbier reactions, Zn and Li activation), and emulsification of immiscible phases (useful with PTC). The bulk liquid stays near ambient temperature.
Light, electricity and flow
- Photochemistry and photoredox catalysis use photons as a traceless reagent; visible light from LEDs is energy-efficient (see Catalysis Across Chemistry).
- Electrosynthesis uses electrons in place of stoichiometric chemical oxidants and reductants.
- Continuous flow reactors hold only a small volume of reacting material at any time (inherently safer for hazardous intermediates such as diazo compounds or azides), give excellent heat transfer, and allow real-time monitoring (principle 11).
6. Renewable Feedstocks
| Source | Platform chemicals | Examples of products |
|---|---|---|
| Starch and sugars | glucose → ethanol, lactic acid, succinic acid by fermentation; 5-hydroxymethylfurfural (HMF) and levulinic acid by acid dehydration | polylactic acid (PLA), bio-ethylene, solvents |
| Hemicellulose (pentoses) | furfural | furfuryl alcohol, 2-MeTHF |
| Lignin | aromatic monomers (vanillin and related phenols) | aromatics, resins |
| Vegetable oils and fats | fatty acids, fatty acid methyl esters, glycerol | biodiesel, surfactants, lubricants |
| CO₂ | C1 building block | urea, salicylic acid (Kolbe–Schmitt), cyclic carbonates and polycarbonates, methanol (with H₂) |
Biodiesel and its glycerol
Triglycerides react with methanol (base catalyst, usually NaOH, KOH or NaOMe) to give fatty acid methyl esters (biodiesel) and glycerol:
$$\text{triglyceride} + 3\,\mathrm{CH_3OH} \longrightarrow 3\,\text{RCOOCH}_3 + \text{glycerol}$$Feedstocks rich in free fatty acids consume the base as soap and form emulsions; they are first esterified with an acid catalyst, or processed with a solid or enzymatic (lipase) catalyst. The glycerol co-product, roughly a tenth of the product mass, is itself a renewable platform chemical (to 1,3-propanediol, epichlorohydrin, glycerol carbonate).
CO₂ as a carbon source
The addition of CO₂ to an epoxide gives a cyclic carbonate with 100% atom economy:
$$\mathrm{C_3H_6O\ (propylene\ oxide) + CO_2 \xrightarrow{\text{catalyst}} C_4H_6O_3\ (propylene\ carbonate)}$$Cyclic carbonates are polar aprotic solvents, electrolyte components, and intermediates to dimethyl carbonate and polycarbonates, offering phosgene-free routes to carbonate chemistry.
7. Safer Reagents and Inherently Safer Design
Dimethyl carbonate (DMC)
DMC is a low-toxicity, biodegradable reagent that can replace three hazardous ones:
| Hazardous reagent | Role | DMC alternative |
|---|---|---|
| Phosgene (COCl₂) | carbonylating agent (carbonates, carbamates, isocyanates) | DMC as a carbonyl source (at lower temperature) |
| Dimethyl sulfate | methylating agent | DMC as a methylating agent (at higher temperature), by-products MeOH and CO₂ |
| Methyl halides | methylating agent | as above, no halide salt waste |
DMC itself can be made without phosgene, for example by copper-catalysed oxidative carbonylation of methanol, \( \mathrm{2CH_3OH + CO + \tfrac12 O_2 \rightarrow (CH_3O)_2CO + H_2O} \), or from cyclic carbonates and methanol.
Inherently safer chemistry: the Bhopal lesson
In December 1984 a release of methyl isocyanate (MIC) from a pesticide plant in Bhopal killed thousands of people. The plant made the insecticide carbaryl by adding 1-naphthol to MIC, which was stored in large tanks. The reaction itself has 100% atom economy; the problem was the stored hazard. An alternative order of steps (1-naphthol with phosgene to the chloroformate, then methylamine) gives the same product without a stock of MIC, though it still uses phosgene and has lower atom economy. Principle 12 asks designers to minimise inventories of hazardous intermediates, make them on demand in small amounts (flow), or avoid them altogether.
8. Industrial Case Studies
Adipic acid without nitrous oxide
Conventional adipic acid (for nylon-6,6) is made by oxidising a cyclohexanol–cyclohexanone mixture with nitric acid, which releases N₂O, a potent greenhouse gas and ozone-depleting substance. A laboratory-scale green alternative oxidises cyclohexene directly with 30% aqueous H₂O₂, catalysed by sodium tungstate with a quaternary ammonium hydrogen sulfate as phase-transfer catalyst, without organic solvent:
$$\mathrm{C_6H_{10} + 4\,H_2O_2 \longrightarrow HOOC(CH_2)_4COOH + 4\,H_2O} \qquad \text{AE} = \frac{146.14}{82.15 + 4(34.01)} = 67.0\%$$The only by-product is water. (Cost of H₂O₂ is the obstacle to industrial adoption.)
Titanium silicalite and H₂O₂ oxidations
Titanium silicalite-1 (TS-1), a zeolite with isolated Ti(IV) sites in a hydrophobic silica framework, activates aqueous H₂O₂ for:
- propylene oxide (by-product water, replacing the chlorohydrin route and its chloride salt waste; atom economy 76% versus 39%, see Green Chemistry Metrics);
- ammoximation of cyclohexanone with NH₃ and H₂O₂ to cyclohexanone oxime for caprolactam (nylon-6), avoiding hydroxylamine sulfate and the large quantities of ammonium sulfate co-product of the classical route;
- hydroxylation of phenol to hydroquinone and catechol.
Design for degradation: detergents and plastics
Early synthetic detergents were branched alkylbenzenesulfonates, which resisted biodegradation and caused persistent foaming in rivers. They were replaced by linear alkylbenzenesulfonates (LAS), whose straight chains are degraded by microbial β-oxidation. In plastics, polylactic acid (PLA), made from fermentation-derived lactic acid, is compostable under industrial conditions, unlike polyethylene.
Summary map
graph LR
A["Hazard or waste"] --> B["Green fix"]
A1["Benzene, CCl₄, DMF"] --> B1["Water, scCO₂, ILs,
DES, solvent-free"]
A2["Long heating,
high T"] --> B2["Microwave, ultrasound,
ball milling, light"]
A3["Petroleum feedstock"] --> B3["Sugars, oils, lignin,
CO₂"]
A4["Phosgene, Me₂SO₄,
stored MIC"] --> B4["DMC, flow, on-demand
intermediates"]
A5["HNO₃/N₂O, Cl₂/lime"] --> B5["H₂O₂ with W or TS-1"]Memory Tricks
Don’t Confuse
| This | vs | That |
|---|---|---|
| Supercritical fluid: above both \( T_c \) and \( P_c \) | Compressed liquid or gas: above only one | |
| scCO₂: non-polar, needs co-solvent for polar solutes | Supercritical water: also behaves non-polar, but needs 374 °C | |
| Ionic liquid: a pure salt, mp < 100 °C | Deep eutectic solvent: a mixture with a depressed eutectic point | |
| Hydrophobic IL ([BMIM][PF₆], [NTf₂]⁻ salts) | Hydrophilic IL ([BMIM][BF₄], [BMIM]Cl) | |
| Microwave: dielectric heating of the bulk | Ultrasound: cavitation, bulk stays cool | |
| Principle 5 (safer solvents) | Principle 3 (less hazardous synthesis: the reagents) | |
| Atom economy (MIC route 100%) | Inherent safety (MIC route was the hazardous one) | |
| DMC as methylating agent (higher T) | DMC as carbonylating agent (lower T) |
Common Mistakes
Practice
All questions below are original practice questions written for this page. They are not from any CSIR NET paper.
Level 1: Foundation
- State the critical temperature and critical pressure of CO₂.
- Define an ionic liquid.
- At what frequency do laboratory microwave reactors usually operate?
Answers
- About 31.1 °C (304.1 K) and 73.8 bar (7.38 MPa).
- A salt with a melting point below 100 °C, usually composed of a bulky organic cation and a weakly coordinating anion.
- 2.45 GHz (wavelength about 12 cm).
Level 2: Part B Style
Practice Q1. Which property of supercritical CO₂ is mainly responsible for its use in decaffeinating coffee?
(a) Its high polarity dissolves caffeine selectively (b) Its solvating power can be tuned by pressure and it leaves no solvent residue on depressurisation (c) It reacts chemically with caffeine to form a carbamate (d) Its critical temperature is above 100 °C, which helps extraction
Answer: (b)
scCO₂ is non-polar (a is wrong; water or a co-solvent is often added to help extract caffeine), does not react with caffeine (c), and has a critical temperature of 31 °C (d). Tunable density and a residue-free product are the reasons.
Practice Q2. Which statement about ionic liquids is incorrect?
(a) They have negligible vapour pressure at room temperature (b) Their miscibility with water can be changed by changing the anion (c) All ionic liquids are non-toxic and readily biodegradable (d) Salts with PF₆⁻ can release HF on hydrolysis
Answer: (c)
Toxicity and biodegradability vary widely; many common imidazolium ILs are poorly biodegradable. Statements (a), (b) and (d) are correct.
Practice Q3. The atom economies of O-methylation of phenol with dimethyl sulfate/NaOH and with dimethyl carbonate are, respectively, closest to:
(a) 58.7% and 41.6% (b) 41.6% and 58.7% (c) 49.2% and 100% (d) 41.6% and 100%
Answer: (b)
Dimethyl sulfate route: 108.14/(94.11 + 126.13 + 40.00) = 41.6%. DMC route: 108.14/(94.11 + 90.08) = 58.7%; methanol and CO₂ are lost, so it is not 100%.
Practice Q4. Equal volumes of four solvents are irradiated at the same microwave power in identical open vessels. Which heats fastest?
(a) n-hexane (b) toluene (c) ethanol (d) carbon tetrachloride
Answer: (c)
Ethanol is polar with a high loss tangent and couples strongly to the field by dipolar polarisation. The other three are non-polar and nearly microwave-transparent.
Level 3: Part C Style
Practice Q5. Cyclohexene is oxidised to adipic acid by 30% aqueous H₂O₂ with Na₂WO₄ and a quaternary ammonium hydrogen sulfate, without organic solvent. Which statements are correct?
- The balanced equation consumes 4 mol H₂O₂ per mol cyclohexene, and the atom economy is about 67%.
- The quaternary ammonium salt acts as a phase-transfer catalyst for the tungsten peroxo species.
- Compared with nitric acid oxidation of cyclohexanol/cyclohexanone, the route avoids N₂O emission.
- Because no organic solvent is used, the E-factor is necessarily zero.
(a) 1 and 2 only (b) 1, 2 and 3 only (c) 3 and 4 only (d) 1, 2, 3 and 4
Answer: (b) 1, 2 and 3 only
- \( \mathrm{C_6H_{10} + 4H_2O_2 \rightarrow C_6H_{10}O_4 + 4H_2O} \); AE = 146.14/(82.15 + 136.06) = 67.0%. True.
- The lipophilic cation carries the anionic tungsten peroxo complex into the organic (cyclohexene) phase. True.
- Nitric acid oxidation releases N₂O; the H₂O₂ route gives only water as by-product. True.
- Water from H₂O₂ and its 70% water content, excess H₂O₂ and any losses are still waste. E is low, not zero. False.
Practice Q6. Triolein (M = 885.4) is transesterified with methanol (M = 32.04) to methyl oleate (M = 296.5) and glycerol (M = 92.09). Which statements are correct?
- The atom economy for methyl oleate as the desired product is about 91%.
- Glycerol makes up about 9% of the total product mass.
- A feedstock with a high free fatty acid content is better processed with NaOH than with an acid catalyst, because NaOH also esterifies free fatty acids.
- Counting glycerol as a co-product, the atom economy is 100%.
(a) 1, 2 and 4 only (b) 1 and 3 only (c) 2 and 3 only (d) 1, 2, 3 and 4
Answer: (a) 1, 2 and 4 only
- AE = 3 × 296.5/(885.4 + 3 × 32.04) = 889.5/981.5 = 90.6%. True.
- 92.09/(889.5 + 92.09) = 9.4%. True.
- NaOH converts free fatty acids into soaps, consuming the catalyst and forming emulsions; acid-catalysed pre-esterification (or a lipase) is used instead. False.
- Transesterification only exchanges groups; all atoms end up in methyl ester or glycerol. True.
Practice Q7. Carbaryl (M = 201.2) can be made (I) by adding 1-naphthol (M = 144.2) to methyl isocyanate (M = 57.05), or (II) by treating 1-naphthol with phosgene (M = 98.92) to give the chloroformate, then with methylamine (M = 31.06). Which statements are correct?
- Route I has 100% atom economy.
- Route II has an atom economy of about 73%, the waste being 2 HCl.
- Route I is therefore inherently safer than route II.
- Route II avoids holding a large inventory of methyl isocyanate, illustrating principle 12, although it still uses a highly toxic reagent.
(a) 1, 2 and 4 only (b) 1 and 3 only (c) 2, 3 and 4 only (d) 1, 2, 3 and 4
Answer: (a) 1, 2 and 4 only
- Addition of an O–H across C=N: every atom is retained. True.
- 201.2/(144.2 + 98.92 + 31.06) = 201.2/274.2 = 73.4%; 274.2 − 201.2 = 73.0 = 2 × HCl (36.46). True.
- Atom economy says nothing about hazard; route I needs stored MIC, the hazard behind the Bhopal disaster. False.
- True. Neither route is ideal; a truly green design would avoid both MIC and phosgene.
Quick Revision Table
| Idea | Formula or fact |
|---|---|
| Preferred solvents | water, ethanol, 2-propanol, ethyl acetate, acetone; replace benzene, CCl₄, CHCl₃, Et₂O, hexane, DMF/NMP, dioxane |
| Water | hydrophobic acceleration of Diels–Alder; on-water and micellar catalysis |
| scCO₂ | \( T_c \) 31.1 °C, \( P_c \) 73.8 bar; tunable, residue-free, miscible with H₂/O₂; non-polar |
| scH₂O | about 374 °C, 22.1 MPa; low dielectric constant; waste oxidation |
| Ionic liquids | salt, mp < 100 °C; [BMIM]⁺, BF₄⁻, PF₆⁻, NTf₂⁻; low vapour pressure, tunable; not automatically green |
| DES | choline chloride : urea 1 : 2; cheap, simple, often biodegradable |
| Microwave | 2.45 GHz, 12 cm; dipolar polarisation, ionic conduction; tan δ = ε″/ε′ |
| Ultrasound | ≥ 20 kHz; cavitation, hot spots, surface activation |
| Mechanochemistry | grinding or ball milling, solvent-free |
| Renewables | sugars → ethanol, lactic acid (PLA), HMF, levulinic acid; furfural; lignin; oils → biodiesel + ~10% glycerol; CO₂ → carbonates |
| DMC | replaces phosgene, Me₂SO₄, MeX; made by oxidative carbonylation of MeOH |
| Bhopal (1984) | stored MIC; principle 12 |
| Adipic acid | H₂O₂/Na₂WO₄/PTC, AE 67%, no N₂O |
| TS-1 | H₂O₂ epoxidation (PO), ammoximation (caprolactam), phenol hydroxylation |
| Degradation | branched → linear alkylbenzenesulfonates; PLA |
Key Takeaways
What’s Next
- Revise the whole unit: Catalysis and Green Chemistry: Quick Revision.
- Previous topic: Green Chemistry: The Twelve Principles and Metrics.
- Biodegradable and bio-based polymers in context: Step-Growth Polymerization Kinetics.
- Surfactants, micelles and emulsions: Colloids: Classification and Properties.
- Chapter overview: Catalysis and Green Chemistry.