Skip to content

Electrolytic Conductance and Kohlrausch's Law

CSIR NET electrochemistry: conductivity, molar conductivity, Kohlrausch's laws, Ostwald dilution law, mobility, transport numbers, Debye–Hückel–Onsager.

  • 19 min read
  • Updated
On this page · 15 sections
  1. Prerequisites
  2. The Hook: Why Pure Water Barely Conducts and Acid Conducts Superbly
  3. 1. Conductance, Conductivity and Molar Conductivity
  4. 2. Strong and Weak Electrolytes
  5. 3. Kohlrausch’s Law of Independent Migration
  6. 4. Ionic Mobility
  7. 5. Transport Numbers
  8. 6. Theory of Conductance: Debye–Hückel–Onsager
  9. Memory Tricks
  10. Don’t Confuse
  11. Common Mistakes
  12. Practice
  13. Quick Revision Table
  14. Key Takeaways
  15. What’s Next

Prerequisites

The Hook: Why Pure Water Barely Conducts and Acid Conducts Superbly

1. Conductance, Conductivity and Molar Conductivity

QuantitySymbol and definitionSI unitCommon unit
ResistanceRΩΩ
ConductanceG = 1/RS (siemens = Ω⁻¹)S
Cell constant\( K_{\text{cell}} = l/A \)m⁻¹cm⁻¹
Conductivity (specific conductance)\( \kappa = G\,(l/A) = G\,K_{\text{cell}} \)S m⁻¹S cm⁻¹
Molar conductivity\( \Lambda_m = \kappa/c \)S m² mol⁻¹S cm² mol⁻¹

With κ in S cm⁻¹ and c in mol L⁻¹:

$$\boxed{\Lambda_m = \frac{1000\,\kappa}{c}\ \ \text{S cm}^2\text{ mol}^{-1}} \qquad 1\ \text{S cm}^2\text{ mol}^{-1} = 10^{-4}\ \text{S m}^2\text{ mol}^{-1}$$

Measuring. Conductance is measured with an AC Wheatstone bridge (typically about 1 kHz) and platinised platinum electrodes, so that electrolysis and polarisation at the electrodes do not falsify the reading. The cell constant is found from a KCl solution of known conductivity; 0.0100 M KCl at 25 °C has κ = 1.413 × 10⁻³ S cm⁻¹. If that solution shows R = 150 Ω, \( K_{\text{cell}} = \kappa R = 1.413 \times 10^{-3} \times 150 = 0.212 \) cm⁻¹.

How κ and Λm change with dilution

  • κ decreases on dilution (fewer ions per unit volume).
  • Λm increases on dilution (for strong electrolytes because interionic drag falls; for weak electrolytes mainly because more of the solute dissociates).

The equivalent conductivity used in older texts is \( \Lambda_{\text{eq}} = \Lambda_m/(\nu_+z_+) \). For a 1:1 salt the two are equal; for CaCl₂, \( \Lambda_m = 2\Lambda_{\text{eq}} \). Read the units in a question carefully.

2. Strong and Weak Electrolytes

Kohlrausch’s square-root law (strong electrolytes)

At low concentration,

$$\boxed{\Lambda_m = \Lambda_m^\circ - K\sqrt{c}}$$

A plot of Λm against \( \sqrt{c} \) is a straight line; its intercept is the limiting molar conductivity \( \Lambda_m^\circ \). K depends mainly on the charge type of the electrolyte.

Weak electrolytes

For acetic acid or aqueous ammonia, Λm is small at ordinary concentrations and rises very steeply only at extreme dilution. The plot against \( \sqrt{c} \) is a curve that approaches the axis almost vertically, so \( \Lambda_m^\circ \) cannot be obtained by extrapolation. Kohlrausch’s second law solves this.

graph TD
    A["Measure Λm at several c"] --> B{"Plot Λm vs √c:
straight line?"} B -->|"Yes: strong electrolyte"| C["Extrapolate to c = 0
intercept = Λm°"] B -->|"No: steep curve,
weak electrolyte"| D["Kohlrausch's law of
independent migration
Λm° = Σ ν λ°"] C --> E["Λm° values of strong electrolytes"] E --> D D --> F["α = Λm / Λm°
Ka = cα² / (1 - α)"]

3. Kohlrausch’s Law of Independent Migration

At infinite dilution, interionic forces vanish and each ion moves independently. The limiting molar conductivity is the sum of the limiting ionic conductivities:

$$\boxed{\Lambda_m^\circ = \nu_+\lambda_+^\circ + \nu_-\lambda_-^\circ}$$

Evidence: the difference \( \Lambda^\circ(\text{KCl}) - \Lambda^\circ(\text{NaCl}) \) is the same as \( \Lambda^\circ(\text{KNO}_3) - \Lambda^\circ(\text{NaNO}_3) \), regardless of the common anion.

Limiting molar ionic conductivities in water at 25 °C (values used on this page, S cm² mol⁻¹):

Cationλ°Anionλ°
H⁺349.8OH⁻198.6
K⁺73.5Cl⁻76.3
NH₄⁺73.5NO₃⁻71.4
Ag⁺61.9CH₃COO⁻40.9
Na⁺50.1
Li⁺38.7

Application 1: Λ° of a weak electrolyte

$$\Lambda_m^\circ(\text{CH}_3\text{COOH}) = \Lambda_m^\circ(\text{HCl}) + \Lambda_m^\circ(\text{CH}_3\text{COONa}) - \Lambda_m^\circ(\text{NaCl})$$$$= 426.1 + 91.0 - 126.4 = 390.7\ \text{S cm}^2\text{ mol}^{-1}$$

The Na⁺ and Cl⁻ contributions cancel, leaving \( \lambda^\circ_{\text{H}^+} + \lambda^\circ_{\text{CH}_3\text{COO}^-} \).

Application 2: degree of dissociation and the Ostwald dilution law

Arrhenius took the fraction dissociated as

$$\alpha = \frac{\Lambda_m}{\Lambda_m^\circ}$$

For HA ⇌ H⁺ + A⁻ at total concentration c:

$$\boxed{K_a = \frac{c\alpha^2}{1 - \alpha} = \frac{c\Lambda_m^2}{\Lambda_m^\circ(\Lambda_m^\circ - \Lambda_m)}}$$

This is Ostwald’s dilution law. When α ≪ 1, \( \alpha \approx \sqrt{K_a/c} \): the weaker the acid or the more concentrated the solution, the smaller the fraction ionised.

Rearranged into a straight line:

$$\frac{1}{\Lambda_m} = \frac{1}{\Lambda_m^\circ} + \frac{c\Lambda_m}{K_a(\Lambda_m^\circ)^2}$$

A plot of \( 1/\Lambda_m \) against \( c\Lambda_m \) has intercept \( 1/\Lambda_m^\circ \) and slope \( 1/(K_a\Lambda_m^{\circ 2}) \), which gives both constants from one data set.

Example. 0.0100 M acetic acid has Λm = 16.2 S cm² mol⁻¹. Then α = 16.2/390.7 = 0.0415 and \( K_a = 0.0100 \times 0.0415^2/0.9585 = 1.8 \times 10^{-5} \).

Application 3: solubility and Ksp of a sparingly soluble salt

A saturated solution of AgCl is so dilute that \( \Lambda_m \approx \Lambda_m^\circ \). Subtract the conductivity of the water used:

$$s = \frac{1000\,\kappa_{\text{salt}}}{\Lambda_m^\circ}, \qquad \kappa_{\text{salt}} = \kappa_{\text{solution}} - \kappa_{\text{water}}$$

With \( \kappa_{\text{solution}} = 3.41 \times 10^{-6} \) and \( \kappa_{\text{water}} = 1.60 \times 10^{-6} \) S cm⁻¹: \( \kappa_{\text{salt}} = 1.81 \times 10^{-6} \) S cm⁻¹, Λ° = 61.9 + 76.3 = 138.2, \( s = 1.31 \times 10^{-5} \) mol L⁻¹, \( K_{sp} = s^2 = 1.7 \times 10^{-10} \).

Application 4: ionic product of water

\( \Lambda_m^\circ(\text{H}_2\text{O} \to \text{H}^+ + \text{OH}^-) = 349.8 + 198.6 = 548.4 \) S cm² mol⁻¹. With \( [\text{H}^+] = [\text{OH}^-] = 1.0 \times 10^{-7} \) M, the conductivity of pure water is \( 548.4 \times 10^{-7}/1000 = 5.5 \times 10^{-8} \) S cm⁻¹, as measured. Run backwards, the measured conductivity gives \( K_w \).

Application 5: transport numbers and the basis of conductometric titrations

The fraction of current carried by each ion follows from the λ° values (Section 5), and the very different λ of H⁺, OH⁻ and other ions explains the shapes of conductometric titration curves.

4. Ionic Mobility

The mobility u of an ion is its drift speed per unit field: \( v = u\,E \) (m² V⁻¹ s⁻¹). Ionic conductivity and mobility are related by

$$\boxed{\lambda_i = |z_i|\,u_iF} \qquad \Lambda_m^\circ = \nu_+z_+u_+F + \nu_-|z_-|u_-F$$

For H⁺: \( u = 349.8/96\,485 = 3.63 \times 10^{-3} \) cm² V⁻¹ s⁻¹ = \( 3.63 \times 10^{-7} \) m² V⁻¹ s⁻¹. For Na⁺: \( 5.19 \times 10^{-8} \) m² V⁻¹ s⁻¹.

What controls mobility

A spherical ion of charge ze and effective (hydrated) radius a, moving through a medium of viscosity η, reaches a terminal speed when the electric force balances Stokes drag: \( zeE = 6\pi\eta a v \), so

$$u = \frac{ze}{6\pi\eta a}$$
  1. Hydrated radius, not crystal radius. Li⁺ is the smallest bare ion of the alkali metals but has the largest hydration shell, so the mobility order is Li⁺ < Na⁺ < K⁺ < Rb⁺ (λ° 38.7, 50.1, 73.5). Large, weakly hydrated ions move fastest.
  2. Viscosity. Walden’s rule: for a given (large) ion in different solvents, \( \lambda^\circ\eta \approx \) constant. Conductivity rises with temperature mainly because the viscosity of water falls.
  3. H⁺ and OH⁻ are anomalous. Their mobilities are several times larger than those of ions of similar size because of the Grotthuss mechanism: a proton is transferred from H₃O⁺ to a neighbouring water molecule along a hydrogen bond, and the hydrogen-bond network then reorients. The charge moves without any single proton travelling far. OH⁻ moves by the reverse hopping of a proton from water to OH⁻. Walden’s rule fails for these ions.

5. Transport Numbers

The transport (transference) number \( t_i \) is the fraction of the total current carried by ion i:

$$\boxed{t_+ = \frac{\nu_+\lambda_+}{\Lambda_m} = \frac{u_+}{u_+ + u_-}\ (\text{1:1}), \qquad t_+ + t_- = 1}$$

At infinite dilution, from the table above:

Electrolyte\( t_+ \)\( t_- \)Comment
HCl0.820.18H⁺ carries most current
KCl0.490.51nearly equal: ideal for salt bridges
NH₄NO₃0.510.49also used in salt bridges
NaCl0.400.60
LiCl0.340.66slow hydrated Li⁺

The transport number of an ion depends on its partner: Cl⁻ carries 18% of the current in HCl but 60% in NaCl.

Hittorf method

Electrolyse a solution between two electrodes in a cell divided into anode, middle and cathode compartments. Analyse the anode and cathode compartments afterwards; the middle compartment should be unchanged (a check that diffusion did not mix them). The charge passed is measured with a coulometer.

Inert electrodes (e.g., HCl with Pt): per faraday passed, the anode compartment loses \( t_+ \) mol of electrolyte and the cathode compartment loses \( t_- \) mol. Hence

$$t_+ = \frac{\text{loss at anode compartment}}{\text{total faradays passed}}, \qquad \frac{\text{loss at anode}}{\text{loss at cathode}} = \frac{t_+}{t_-} = \frac{u_+}{u_-}$$

Attackable anode (AgNO₃ with silver electrodes): per faraday, 1 mol Ag⁺ enters the anode compartment by dissolution and \( t_+ \) mol leave by migration, while \( t_- \) mol NO₃⁻ arrive. The anode compartment gains \( t_- \) mol of AgNO₃.

Worked example. In a Hittorf experiment with silver electrodes in AgNO₃, a coulometer shows that 0.00320 mol of electrons passed. The anode compartment contained 0.01500 mol AgNO₃ before and 0.01671 mol after (same mass of water). Gain = 0.00171 mol = \( t_- \times 0.00320 \), so \( t_{\text{NO}_3^-} = 0.534 \) and \( t_{\text{Ag}^+} = 0.466 \).

Moving boundary method

A sharp boundary between the solution under study (e.g., HCl) and a following solution with a slower cation of the same anion (e.g., CdCl₂) moves through a tube of uniform cross-section as current flows. If the boundary sweeps a volume V while charge Q passes through a solution of concentration c:

$$\boxed{t_+ = \frac{z_+cVF}{Q}}$$

For 0.0100 M HCl, a charge of 3.00 C moving the boundary through 2.55 cm³ gives \( t_+ = (1.00 \times 10^{-5}\ \text{mol cm}^{-3})(2.55)(96\,485)/3.00 = 0.820 \).

EMF method

The ratio of the potentials of concentration cells with and without transference gives \( t_+ \) or \( t_- \) directly (see Concentration Cells and Liquid Junctions).

6. Theory of Conductance: Debye–Hückel–Onsager

Why does Λm fall as \( \sqrt{c} \) for strong electrolytes? Two effects of the ionic atmosphere slow a moving ion:

  1. Relaxation (asymmetry) effect. As the ion moves, its atmosphere has to be rebuilt ahead and decays behind it; this takes a finite relaxation time. The atmosphere is therefore slightly displaced behind the ion, and its opposite charge pulls the ion backwards.
  2. Electrophoretic effect. The atmosphere ions, with their solvation shells, move in the opposite direction under the field and drag solvent with them. The central ion swims upstream.

Both effects scale with the inverse Debye length, \( \kappa \propto \sqrt{c} \). Onsager’s result for a 1:1 electrolyte:

$$\boxed{\Lambda_m = \Lambda_m^\circ - (\mathcal{A} + \mathcal{B}\Lambda_m^\circ)\sqrt{c}}$$

where \( \mathcal{A} \) is the electrophoretic term and \( \mathcal{B}\Lambda_m^\circ \) the relaxation term. For water at 25 °C, \( \mathcal{A} \approx 60.2 \) S cm² mol⁻¹ (mol L⁻¹)⁻¹ᐟ² and \( \mathcal{B} \approx 0.229 \) (mol L⁻¹)⁻¹ᐟ². For KCl (Λ° = 149.8) the predicted slope is \( 60.2 + 0.229 \times 149.8 = 94.5 \), close to the experimental Kohlrausch slope. The equation gives a theoretical basis to Kohlrausch’s empirical law and, like the limiting law for activity, holds only in dilute solution (roughly below 10⁻³ M).

Both constants depend on the solvent: \( \mathcal{A} \propto 1/[\eta(\varepsilon_rT)^{1/2}] \) and \( \mathcal{B} \propto (\varepsilon_rT)^{-3/2} \).

Two effects that confirm the atmosphere

EffectConditionObservationReason
Wien effectvery high electric fieldconductivity rises towards \( \Lambda^\circ \)ions move so fast that the atmosphere cannot form around them; both drags disappear. For weak electrolytes the field also increases dissociation (second Wien effect)
Debye–Falkenhagen effecthigh-frequency AC fieldconductivity risesthe field reverses faster than the atmosphere relaxes; the asymmetric atmosphere never builds up, so the relaxation drag vanishes (the electrophoretic one remains)

Memory Tricks

Don’t Confuse

ThisvsThat
Conductivity κ: falls on dilutionmolar conductivity Λm: rises on dilution
Strong electrolyte: Λm linear in \( \sqrt{c} \), extrapolateweak electrolyte: use independent migration, never extrapolate
Λm drops for strong electrolytes because of interionic dragfor weak electrolytes because α falls
Mobility u (m² V⁻¹ s⁻¹, per ion)ionic conductivity λ = |z|uF (S m² mol⁻¹)
Transport number: depends on the partner ionlimiting ionic conductivity: property of the ion alone
Wien effect (high field strength)Debye–Falkenhagen effect (high frequency)
Molar conductivity of CaCl₂equivalent conductivity = Λm/2

Common Mistakes

Practice

All questions below are original practice questions written for this page. They are not from any CSIR NET paper. Use the λ° table above and F = 96 485 C mol⁻¹.

Level 1: Foundation

  1. A conductivity cell filled with 0.0100 M KCl (κ = 1.413 × 10⁻³ S cm⁻¹) has a resistance of 150 Ω. Find the cell constant.
  2. Calculate Λ°(CH₃COOH) from Λ°(HCl) = 426.1, Λ°(CH₃COONa) = 91.0 and Λ°(NaCl) = 126.4 S cm² mol⁻¹.
  3. Arrange Li⁺, Na⁺, K⁺, H⁺ in increasing order of ionic mobility in water.
Answers
  1. \( K_{\text{cell}} = \kappa R = 1.413 \times 10^{-3} \times 150 = \) 0.212 cm⁻¹.
  2. 426.1 + 91.0 − 126.4 = 390.7 S cm² mol⁻¹.
  3. Li⁺ < Na⁺ < K⁺ < H⁺ (hydrated size; Grotthuss mechanism for H⁺).

Level 2: Part B Style

Practice Q1. The molar conductivity of 0.0100 M acetic acid is 16.2 S cm² mol⁻¹ and Λ° = 390.7 S cm² mol⁻¹. The dissociation constant is about:

(a) \( 1.7 \times 10^{-3} \) (b) \( 4.1 \times 10^{-4} \) (c) \( 1.8 \times 10^{-5} \) (d) \( 1.7 \times 10^{-7} \)

Answer: (c)

α = 16.2/390.7 = 0.0415. \( K_a = c\alpha^2/(1-\alpha) = 0.0100 \times 0.001719/0.9585 = 1.79 \times 10^{-5} \). Option (b) is \( c\alpha \) (the [H⁺]); (a) is \( \alpha^2 \).

Practice Q2. A saturated aqueous solution of AgCl has κ = 3.41 × 10⁻⁶ S cm⁻¹; the water used has κ = 1.60 × 10⁻⁶ S cm⁻¹. With λ°(Ag⁺) = 61.9 and λ°(Cl⁻) = 76.3 S cm² mol⁻¹, Ksp of AgCl is about:

(a) \( 1.3 \times 10^{-5} \) (b) \( 1.7 \times 10^{-10} \) (c) \( 6.1 \times 10^{-10} \) (d) \( 2.5 \times 10^{-5} \)

Answer: (b)

\( \kappa_{\text{AgCl}} = 1.81 \times 10^{-6} \) S cm⁻¹; Λ° = 138.2; \( s = 1000 \times 1.81 \times 10^{-6}/138.2 = 1.31 \times 10^{-5} \) M; \( K_{sp} = 1.7 \times 10^{-10} \). Option (c) forgets to subtract water ((2.47 × 10⁻⁵)²); (a) is s itself.

Practice Q3. The transport number of H⁺ in very dilute HCl, from λ°(H⁺) = 349.8 and λ°(Cl⁻) = 76.3 S cm² mol⁻¹, is:

(a) 0.18 (b) 0.50 (c) 0.82 (d) 4.6

Answer: (c)

\( t_+ = 349.8/(349.8 + 76.3) = 349.8/426.1 = 0.821 \). Option (a) is \( t_- \); (d) is the ratio \( \lambda_+/\lambda_- \).

Practice Q4. Which statement about the Debye–Hückel–Onsager equation is incorrect?

(a) It predicts that Λm of a strong electrolyte falls linearly with \( \sqrt{c} \) at low concentration. (b) The relaxation term is proportional to Λ°m. (c) It applies equally well to acetic acid at 0.1 M. (d) It contains an electrophoretic term that does not depend on Λ°m.

Answer: (c)

The equation assumes complete dissociation and dilute solution. Acetic acid is a weak electrolyte; its Λm falls mainly because α falls, which the equation does not describe. (a), (b) and (d) are correct features of \( \Lambda_m = \Lambda_m^\circ - (\mathcal{A} + \mathcal{B}\Lambda_m^\circ)\sqrt{c} \).

Level 3: Part C Style

Practice Q5. Molar conductivities (S cm² mol⁻¹) of two electrolytes X and Y in water at 25 °C (illustrative data):

c / mol L⁻¹0.000100.000400.000900.00160
X148.9147.9147.0146.0
Y134.374.651.539.3

Which statements are correct?

  1. X is a strong electrolyte with Λ° close to 149.8 S cm² mol⁻¹.
  2. The Kohlrausch slope for X is about 95 S cm² mol⁻¹ (mol L⁻¹)⁻¹ᐟ².
  3. Λ° of Y can be found reliably by extrapolating Λm against \( \sqrt{c} \).
  4. Y behaves as a weak electrolyte; its Λ° must come from Kohlrausch’s law of independent migration.

(a) 1, 2 and 4 only (b) 1 and 3 only (c) 2 and 3 only (d) 1, 2, 3 and 4

Answer: (a) 1, 2 and 4 only

\( \sqrt{c} \) = 0.010, 0.020, 0.030, 0.040.

X: Λm falls by about 0.95 per 0.010 of \( \sqrt{c} \): slope ≈ 0.95/0.010 = 95; intercept 148.9 + 0.95 = 149.85. Linear, so strong (it behaves like KCl, whose Onsager slope is 94.5). Statements 1 and 2 are correct.

Y: Λm drops from 134.3 to 39.3 as \( \sqrt{c} \) only goes from 0.010 to 0.040, and the drop per step shrinks (60, 23, 12): a steep curve, not a line. This is the behaviour of a weak acid (the numbers fit Λ° = 390.7 and \( K_a = 1.8 \times 10^{-5} \), acetic acid); an extrapolation would be unreliable (statement 3 wrong). Its Λ° comes from independent migration (statement 4 correct).

Practice Q6. In a Hittorf experiment on AgNO₃ with silver electrodes, 0.00320 mol of electrons passed. The anode compartment contained 0.01500 mol AgNO₃ before electrolysis and 0.01671 mol after (same mass of water). Which statements are correct?

  1. \( t(\text{NO}_3^-) = 0.534 \).
  2. \( t(\text{Ag}^+) = 0.466 \).
  3. With inert platinum electrodes, the anode compartment would have lost electrolyte.
  4. The ratio of ionic mobilities \( u(\text{Ag}^+)/u(\text{NO}_3^-) \) is about 0.87.

(a) 1, 2, 3 and 4 (b) 1 and 2 only (c) 1, 2 and 3 only (d) 3 and 4 only

Answer: (a) 1, 2, 3 and 4

Per faraday at a silver anode: +1 Ag⁺ (dissolution), \( -t_+ \) Ag⁺ (migration out), \( +t_- \) NO₃⁻ (migration in). Net gain of AgNO₃ = \( t_- \).

Gain = 0.01671 − 0.01500 = 0.00171 mol; \( t_- = 0.00171/0.00320 = 0.534 \); \( t_+ = 0.466 \).

With inert electrodes the anode oxidises water, so no Ag⁺ enters: the compartment loses \( t_+ \) per faraday (statement 3 correct).

\( u_+/u_- = t_+/t_- = 0.466/0.534 = 0.873 \) (statement 4 correct). The λ° table gives 61.9/71.4 = 0.867, in good agreement.

Practice Q7. Which statements are correct?

  1. The conductivity of pure water at 25 °C calculated from λ°(H⁺) + λ°(OH⁻) = 548.4 S cm² mol⁻¹ and \( K_w = 1.0 \times 10^{-14} \) is about \( 5.5 \times 10^{-8} \) S cm⁻¹.
  2. Walden’s rule holds well for H⁺ in water and in methanol.
  3. The Wien effect is an increase in conductance at very high electric field strength.
  4. In the moving boundary method, the following (indicator) solution must contain a cation that is slower than the cation being studied.

(a) 1, 3 and 4 only (b) 1 and 2 only (c) 2 and 3 only (d) 1, 2, 3 and 4

Answer: (a) 1, 3 and 4 only
  1. Correct. \( \kappa = 548.4 \times 1.0 \times 10^{-7}/1000 = 5.5 \times 10^{-8} \) S cm⁻¹.
  2. Wrong. H⁺ moves by proton hopping, which depends on the hydrogen-bond network, not on Stokes drag; Walden’s rule fails for it.
  3. Correct. At high fields the ions outrun their atmospheres.
  4. Correct. A slower following ion keeps the boundary sharp (e.g., Cd²⁺ behind H⁺).

Quick Revision Table

IdeaFormula or fact
Cell constant\( K_{\text{cell}} = l/A = \kappa R \); 0.0100 M KCl: κ = 1.413 × 10⁻³ S cm⁻¹ (25 °C)
Molar conductivity\( \Lambda_m = 1000\kappa/c \) (S cm² mol⁻¹)
Kohlrausch (strong)\( \Lambda_m = \Lambda_m^\circ - K\sqrt{c} \)
Independent migration\( \Lambda_m^\circ = \nu_+\lambda_+^\circ + \nu_-\lambda_-^\circ \)
Weak acidΛ°(HA) = Λ°(HCl) + Λ°(NaA) − Λ°(NaCl); acetic acid 390.7
Ostwald\( K_a = c\alpha^2/(1-\alpha) \), \( \alpha = \Lambda_m/\Lambda_m^\circ \)
Solubility\( s = 1000(\kappa_{\text{soln}} - \kappa_{\text{water}})/\Lambda_m^\circ \)
Mobility\( \lambda = \vert z\vert uF \); H⁺ 3.63 × 10⁻⁷ m² V⁻¹ s⁻¹
OrderLi⁺ < Na⁺ < K⁺; H⁺ (349.8) ≫ OH⁻ (198.6) ≫ others
Walden\( \lambda^\circ\eta \approx \) constant (fails for H⁺, OH⁻)
Transport number\( t_+ = \lambda_+/\Lambda \); HCl 0.82, KCl 0.49, NaCl 0.40
Hittorf (inert)anode loses \( t_+ \), cathode loses \( t_- \) per faraday
Moving boundary\( t_+ = z_+cVF/Q \)
DHO\( \Lambda_m = \Lambda_m^\circ - (60.2 + 0.229\Lambda_m^\circ)\sqrt{c} \) (1:1, water, 25 °C)
Wien / Debye–Falkenhagenhigh field / high frequency raise conductance

Key Takeaways

What’s Next