Chain-Growth Polymerisation Kinetics
CSIR NET polymer kinetics: radical rate and kinetic chain length, chain transfer (Mayo), ceiling temperature, living anionic, cationic and copolymerisation.
- 21 min
On this page · 15 sections
- Prerequisites
- The Hook: The Reaction That Speeds Up as It Thickens
- 1. Free-Radical Polymerisation
- 2. Temperature Dependence
- 3. Chain Transfer
- 4. Thermodynamics: The Ceiling Temperature
- 5. Ionic Polymerisation
- 6. Copolymerisation
- Memory Tricks
- Don’t Confuse
- Common Mistakes
- Practice
- Quick Revision Table
- Key Takeaways
- What’s Next
Prerequisites
- Steady-state approximation for reactive intermediates: Complex Reactions and the Steady-State Approximation.
- Chain reactions (initiation, propagation, termination) and the first look at radical polymerisation: Reaction Mechanisms and Chain Reactions.
- Composite activation energies: Rate Laws and Temperature Dependence.
- Molar mass averages, Poisson and most probable distributions: Molar Mass Averages and Distributions.
The Hook: The Reaction That Speeds Up as It Thickens
1. Free-Radical Polymerisation
The mechanism
| Step | Reaction | Rate |
|---|---|---|
| Initiator decomposition | \( \mathrm{I \rightarrow 2R^\bullet} \) | \( k_d[\mathrm{I}] \) |
| Initiation | \( \mathrm{R^\bullet + M \rightarrow RM^\bullet} \) (fraction \( f \) of radicals succeed) | \( R_i = 2fk_d[\mathrm{I}] \) |
| Propagation | \( \mathrm{RM_n^\bullet + M \rightarrow RM_{n+1}^\bullet} \) | \( R_p = k_p[\mathrm{M}][\mathrm{M^\bullet}] \) |
| Termination by combination | \( \mathrm{M_n^\bullet + M_m^\bullet \rightarrow M_{n+m}} \) | \( R_t = 2k_t[\mathrm{M^\bullet}]^2 \) |
| Termination by disproportionation | \( \mathrm{M_n^\bullet + M_m^\bullet \rightarrow M_n + M_m} \) (H transfer: one saturated, one unsaturated end) | (included in \( k_t \)) |
Common thermal initiators are azo compounds such as AIBN (2,2′-azobisisobutyronitrile) and peroxides such as benzoyl peroxide; redox pairs and photoinitiators are used at lower temperatures. The initiator efficiency \( f \) (usually less than 1) accounts for radical pairs that recombine or react inside their solvent cage before escaping (the cage effect). The initiator half-life is \( t_{1/2} = \ln 2/k_d \).
Steady state and the rate of polymerisation
Radicals reach a steady state within seconds: \( R_i = R_t \), so \( 2fk_d[\mathrm{I}] = 2k_t[\mathrm{M^\bullet}]^2 \) and
$$[\mathrm{M^\bullet}] = \left(\frac{fk_d[\mathrm{I}]}{k_t}\right)^{1/2}$$Monomer is consumed almost entirely by propagation (each initiation uses one monomer, each chain hundreds), so
$$\boxed{R_p = k_p[\mathrm{M}]\left(\frac{fk_d[\mathrm{I}]}{k_t}\right)^{1/2}}$$First order in monomer, half order in initiator. The half order is the signature of bimolecular termination; first-order termination (for example by a primary radical or an inhibitor) would make \( R_p \) first order in \( [\mathrm{I}] \).
If initiation itself depends on monomer (\( R_i = 2fk_d[\mathrm{I}][\mathrm{M}] \), as when the primary radical’s capture by monomer is rate-limiting), \( R_p \propto [\mathrm{M}]^{3/2} \).
Kinetic chain length and degree of polymerisation
The kinetic chain length \( \nu \) is the average number of monomers added per radical that starts a chain:
$$\boxed{\nu = \frac{R_p}{R_i} = \frac{k_p[\mathrm{M}]}{2(fk_dk_t[\mathrm{I}])^{1/2}} = \frac{k_p^2[\mathrm{M}]^2}{2k_tR_p}}$$| Termination mode | \( X_n \) (no transfer) | Đ (low conversion) |
|---|---|---|
| Combination (two kinetic chains in one molecule) | \( 2\nu \) | 1.5 |
| Disproportionation (one kinetic chain per molecule) | \( \nu \) | 2 |
The last form of \( \nu \) is the important one: at fixed monomer, anything that speeds up the polymerisation by raising the radical concentration shortens the chains. Four times the initiator gives twice the rate and half the chain length.
Dead-end polymerisation
If the initiator decays appreciably, \( [\mathrm{I}] = [\mathrm{I}]_0e^{-k_dt} \), and integrating \( R_p \) gives
$$\ln\frac{[\mathrm{M}]_0}{[\mathrm{M}]} = 2k_p\left(\frac{f[\mathrm{I}]_0}{k_dk_t}\right)^{1/2}\left(1 - e^{-k_dt/2}\right)$$As \( t \to \infty \) the conversion levels off below 100%: the initiator runs out first.
Autoacceleration: the gel (Trommsdorff–Norrish) effect
At moderate to high conversion in bulk or concentrated solution, viscosity rises and termination, which needs two large radicals to diffuse together, becomes diffusion-controlled: \( k_t \) falls by orders of magnitude while \( k_p \) (a small monomer diffusing to a chain end) is barely affected. Both \( R_p \propto k_t^{-1/2} \) and \( X_n \propto k_t^{-1/2} \) rise; the exotherm can run away, and the distribution broadens. Methyl methacrylate shows it strongly. At still higher conversion, close to the glass transition of the polymer–monomer mixture, even propagation becomes diffusion-limited (the glass effect) and the reaction stalls short of full conversion.
2. Temperature Dependence
Write each rate constant in Arrhenius form. Since \( R_p \propto k_p(k_d/k_t)^{1/2} \) and \( X_n \propto k_p/(k_dk_t)^{1/2} \),
$$\boxed{E_R = E_p + \tfrac{1}{2}E_d - \tfrac{1}{2}E_t, \qquad E_{X_n} = E_p - \tfrac{1}{2}E_d - \tfrac{1}{2}E_t}$$For thermal initiators \( E_d \) is large (of order 120–150 kJ mol⁻¹), \( E_p \) is moderate and \( E_t \) small. So \( E_R \) is large and positive while \( E_{X_n} \) is negative: heating speeds the polymerisation but shortens the chains.
With photochemical initiation, \( R_i \) depends on light intensity and not on temperature, so \( E_d \) drops out: \( E_R = E_{X_n} = E_p - \tfrac{1}{2}E_t \), small and positive (25 kJ mol⁻¹ for the numbers above, a factor of about 1.3 per 10 K near 60 °C).
3. Chain Transfer
A growing radical can abstract an atom (usually H or a halogen) from another molecule XA, ending its own growth and starting a new radical:
$$\mathrm{M_n^\bullet + XA \rightarrow M_nX + A^\bullet}, \qquad \mathrm{A^\bullet + M \rightarrow AM^\bullet}\ (\text{fast})$$If \( \mathrm{A^\bullet} \) re-initiates quickly, the kinetic chain continues (so \( R_p \) is unchanged) but the polymer molecule ends (so \( X_n \) falls). Transfer can occur to monomer, solvent, initiator, polymer (giving branches) or a deliberately added chain-transfer agent (thiols are typical).
The Mayo equation
Define transfer constants \( C = k_{tr}/k_p \) for each species. For termination by disproportionation (or with \( (1/X_n)_0 \) taken from the transfer-free experiment),
$$\boxed{\frac{1}{X_n} = \left(\frac{1}{X_n}\right)_0 + C_M + C_S\frac{[\mathrm{S}]}{[\mathrm{M}]} + C_I\frac{[\mathrm{I}]}{[\mathrm{M}]}}$$A plot of \( 1/X_n \) against \( [\mathrm{S}]/[\mathrm{M}] \) at constant \( R_p \) is linear with slope \( C_S \). \( C_M \) sets an upper limit on \( X_n \) that no reduction in initiator can exceed: \( X_n \le 1/C_M \).
Inhibition, retardation and degradative transfer
| Additive behaviour | Effect on \( R_p \) | Effect on \( X_n \) |
|---|---|---|
| Normal chain transfer (A• re-initiates fast) | unchanged | lowered |
| Degradative transfer (A• too stable to re-initiate well; e.g. allylic monomers) | lowered | lowered |
| Retarder (traps some radicals) | lowered, no induction period | lowered |
| Inhibitor (traps essentially every radical until consumed) | zero during an induction period, then normal | — |
Stable radicals such as DPPH and many quinones act as inhibitors; dissolved oxygen also inhibits many radical polymerisations. Commercial monomers are shipped with an inhibitor that must be removed or overwhelmed before use.
4. Thermodynamics: The Ceiling Temperature
Propagation is reversible in principle: \( \mathrm{M_n^\bullet + M \rightleftharpoons M_{n+1}^\bullet} \). Converting a C=C π bond into a σ bond makes \( \Delta H_p \) negative; joining many molecules into one makes \( \Delta S_p \) negative. So
$$\Delta G_p = \Delta H_p - T\Delta S_p$$becomes zero at the ceiling temperature. At equilibrium, with \( K = 1/[\mathrm{M}]_e \) (1 mol L⁻¹ standard state),
$$\ln[\mathrm{M}]_e = \frac{\Delta H_p}{RT} - \frac{\Delta S_p^\circ}{R}, \qquad \boxed{T_c = \frac{\Delta H_p}{\Delta S_p^\circ + R\ln[\mathrm{M}]}}$$Above \( T_c \) a polymer of that monomer at that concentration depolymerises. \( T_c \) falls when the monomer is diluted, and it is low for monomers whose \( \Delta H_p \) is small because of steric strain in the polymer (1,1-disubstituted monomers; α-methylstyrene is the classic case).
5. Ionic Polymerisation
| Feature | Anionic | Cationic |
|---|---|---|
| Suitable monomers | electron-withdrawing substituents (acrylonitrile, methacrylates, cyanoacrylates), styrene, dienes; epoxides by ring opening | electron-donating substituents: isobutylene, vinyl ethers, styrene; cyclic ethers |
| Initiators | organolithiums (n-BuLi), alkali-metal naphthalenides (electron transfer), alkoxides, amide ion | protic acids; Lewis acid + co-initiator (e.g. BF₃ + H₂O) |
| Termination | absent in pure aprotic systems: living | frequent; transfer to monomer dominates |
| Temperature | often room temperature or below | low temperatures needed for high \( M \) |
| Solvent effect | free ions propagate much faster than ion pairs; polar solvents (THF) raise the rate | likewise, counter-ion and solvent control ion-pair separation |
Living anionic polymerisation
In carefully purified aprotic systems (no water, oxygen, CO₂ or protic impurities) carbanion chain ends have no way to terminate. Szwarc’s polymerisation of styrene with sodium naphthalenide in THF (1956) gave chains that resumed growing when more monomer was added: living polymers.
If initiation is fast compared with propagation, every chain starts at once and
$$R_p = k_p[\mathrm{M}][\mathrm{M^-}], \qquad [\mathrm{M^-}] = [\mathrm{I}]_0 = \text{constant}$$so \( \ln([\mathrm{M}]_0/[\mathrm{M}]) = k_p[\mathrm{I}]_0t \): first order in monomer, first order in initiator (not half order). The degree of polymerisation is set by stoichiometry:
$$\boxed{X_n = \frac{p[\mathrm{M}]_0}{[\mathrm{I}]_0}\ \text{(monofunctional initiator)}, \qquad X_n = \frac{2p[\mathrm{M}]_0}{[\mathrm{I}]_0}\ \text{(naphthalenide)}}$$where \( p \) is the fractional monomer conversion. The factor 2 for sodium naphthalenide is because the styrene radical anions formed by electron transfer dimerise into a dianion that grows from both ends, so two naphthalenide ions make one chain. \( X_n \) grows linearly with conversion, and the Poisson distribution gives Đ ≈ 1 + 1/\( X_n \).
Living ends allow block copolymers by sequential monomer addition (styrene, then a diene, then styrene again gives a thermoplastic elastomer architecture), and end-functional polymers by deliberate termination (CO₂ then acid gives a carboxyl end; ethylene oxide gives a hydroxyl end).
Controlled (“living”) radical methods, such as nitroxide-mediated polymerisation (NMP), atom-transfer radical polymerisation (ATRP) and reversible addition–fragmentation chain transfer (RAFT), keep most chains dormant most of the time, so that they too grow together and give low Đ, although termination is not absent.
Cationic polymerisation kinetics
With a Lewis-acid initiator I and co-initiator ZY in equilibrium (\( K \)), initiation \( R_i = Kk_i[\mathrm{I}][\mathrm{ZY}][\mathrm{M}] \) and unimolecular termination \( R_t = k_t[\mathrm{M^+}] \) (combination with the counter-ion). Steady state gives
$$R_p = \frac{Kk_ik_p}{k_t}[\mathrm{I}][\mathrm{ZY}][\mathrm{M}]^2$$and, including transfer to monomer,
$$\frac{1}{X_n} = \frac{k_t}{k_p[\mathrm{M}]} + C_M$$Because termination is first order in active centres, \( R_p \) is first order in initiator (contrast the half order of radical polymerisation). Transfer to monomer usually dominates, and because its activation energy exceeds that of propagation, low temperatures (well below 0 °C for isobutylene) are needed for high molar mass.
6. Copolymerisation
When two monomers M₁ and M₂ polymerise together, the terminal model assumes the reactivity of a chain end depends only on its last unit. Four propagation steps:
| Chain end + monomer | Rate constant |
|---|---|
| \( \mathrm{\sim M_1^\bullet + M_1} \) | \( k_{11} \) |
| \( \mathrm{\sim M_1^\bullet + M_2} \) | \( k_{12} \) |
| \( \mathrm{\sim M_2^\bullet + M_2} \) | \( k_{22} \) |
| \( \mathrm{\sim M_2^\bullet + M_1} \) | \( k_{21} \) |
Reactivity ratios: \( r_1 = k_{11}/k_{12} \), \( r_2 = k_{22}/k_{21} \). Each compares how much a chain end prefers its own monomer to the other.
The copolymer (Mayo–Lewis) equation
Applying a steady state to the two chain-end types (\( k_{12}[\mathrm{M_1^\bullet}][\mathrm{M_2}] = k_{21}[\mathrm{M_2^\bullet}][\mathrm{M_1}] \)):
$$\frac{\mathrm{d}[\mathrm{M_1}]}{\mathrm{d}[\mathrm{M_2}]} = \frac{[\mathrm{M_1}](r_1[\mathrm{M_1}] + [\mathrm{M_2}])}{[\mathrm{M_2}]([\mathrm{M_1}] + r_2[\mathrm{M_2}])}$$In mole fractions (\( f_1 \) in the feed, \( F_1 \) in the copolymer being formed):
$$\boxed{F_1 = \frac{r_1f_1^2 + f_1f_2}{r_1f_1^2 + 2f_1f_2 + r_2f_2^2}}$$| Reactivity ratios | Copolymer type | Behaviour |
|---|---|---|
| \( r_1r_2 = 1 \) | ideal (random) | \( F_1/F_2 = r_1f_1/f_2 \); each end has the same preference |
| \( r_1 = r_2 = 1 \) | ideal, \( F_1 = f_1 \) | composition equals feed |
| \( r_1 \approx r_2 \approx 0 \) | alternating | \( F_1 = 0.5 \) at almost any feed (styrene–maleic anhydride is the classic case) |
| \( 0 < r_1r_2 < 1 \), both \( r < 1 \) | tendency to alternate | azeotropic feed at \( f_1 = (1 - r_2)/(2 - r_1 - r_2) \) |
| \( r_1 > 1 \), \( r_2 < 1 \) | M₁ enters faster | copolymer richer in M₁ than the feed; feed drifts to M₂ |
| \( r_1 > 1 \), \( r_2 > 1 \) | blocky / homopolymer mixture | rare in radical systems |
At the azeotropic composition, copolymer and feed have the same composition, so the composition does not drift with conversion. Elsewhere the faster monomer is used up first and the copolymer formed late in a batch differs from that formed early (composition drift). The Alfrey–Price Q–e scheme is an empirical way of estimating \( r_1 \) and \( r_2 \) from a resonance parameter Q and a polarity parameter e assigned to each monomer.
Coordination (Ziegler–Natta and metallocene) polymerisation, which controls tacticity, is treated mechanistically on Homogeneous Catalysis.
Memory Tricks
Don’t Confuse
| This | vs | That |
|---|---|---|
| Kinetic chain length \( \nu = R_p/R_i \) | \( X_n \): \( 2\nu \) (combination) or \( \nu \) (disproportionation), smaller with transfer | |
| Radical: \( R_p \propto [\mathrm{I}]^{1/2} \) (bimolecular termination) | Living anionic and cationic: \( R_p \propto [\mathrm{I}]^1 \) | |
| Chain transfer: \( R_p \) unchanged | Retardation / degradative transfer: \( R_p \) lowered | |
| Inhibitor: induction period, then normal rate | Retarder: no induction period, lower rate throughout | |
| Gel (Trommsdorff) effect: \( k_t \) falls, rate up | Gel point (step growth): network forms | |
| Ideal copolymer (\( r_1r_2 = 1 \)) | “Ideal” does not mean random 50:50; it means \( F_1 = f_1 \) only if \( r_1 = r_2 = 1 \) | |
| Ceiling temperature: polymer unstable above \( T_c \) | Glass transition: a physical change in the solid polymer |
Common Mistakes
Practice
All questions below are original practice questions written for this page. They are not from any CSIR NET paper.
Level 1: Foundation
- Write \( R_p \) for free-radical polymerisation with bimolecular termination.
- What is the kinetic chain length if \( R_p = 2.0 \times 10^{-4} \) and \( R_i = 4.0 \times 10^{-7} \) mol L⁻¹ s⁻¹?
- For a copolymerisation with \( r_1 = r_2 = 0 \), what is \( F_1 \) for a feed with \( f_1 = 0.8 \)?
Answers
- \( R_p = k_p[\mathrm{M}]\,(fk_d[\mathrm{I}]/k_t)^{1/2} \).
- \( \nu = R_p/R_i = 500 \).
- \( F_1 = 0.5 \): strictly alternating.
Level 2: Part B Style
Practice Q1. In a radical polymerisation (termination by combination, no transfer), both monomer concentration and initiator concentration are doubled. \( R_p \) and \( X_n \) change by factors of:
(a) 2√2 and √2 (b) 4 and 1 (c) 2√2 and 1/√2 (d) 2 and 2
Answer: (a)
\( R_p \propto [\mathrm{M}][\mathrm{I}]^{1/2} \): \( 2 \times \sqrt{2} = 2\sqrt{2} \). \( X_n \propto [\mathrm{M}][\mathrm{I}]^{-1/2} \): \( 2/\sqrt{2} = \sqrt{2} \).
Practice Q2. For thermally initiated radical polymerisation with \( E_d = 140 \), \( E_p = 25 \) and \( E_t = 10 \) kJ mol⁻¹ (illustrative), the activation energies for \( R_p \) and \( X_n \) (kJ mol⁻¹) are:
(a) 90 and −50 (b) 160 and −125 (c) 90 and 50 (d) 20 and 20
Answer: (a)
\( E_R = 25 + 70 - 5 = 90 \); \( E_{X_n} = 25 - 70 - 5 = -50 \). Option (d) is the photo-initiated case.
Practice Q3. Styrene (0.50 mol) is polymerised in cyclohexane to 80% conversion with \( 1.0 \times 10^{-3} \) mol n-BuLi under living conditions. \( \overline{M}_n \) (g mol⁻¹, ignoring end groups; monomer 104.15 g mol⁻¹) is about:
(a) 52,000 (b) 41,700 (c) 83,300 (d) 20,800
Answer: (b) 41,700
Monomer reacted \( = 0.80 \times 0.50 = 0.40 \) mol; \( X_n = 0.40/0.0010 = 400 \); \( \overline{M}_n = 400 \times 104.15 \approx 41{,}700 \). Option (a) ignores the conversion; (c) uses the naphthalenide factor 2.
Practice Q4. For reactivity ratios \( r_1 = 0.4 \) and \( r_2 = 0.1 \), the azeotropic feed composition \( f_1 \) is:
(a) 0.20 (b) 0.40 (c) 0.60 (d) 0.80
Answer: (c) 0.60
\( f_1 = (1 - r_2)/(2 - r_1 - r_2) = 0.9/1.5 = 0.60 \).
Level 3: Part C Style
Practice Q5. A radical polymerisation has \( [\mathrm{M}] = 5.0 \) mol L⁻¹, \( [\mathrm{I}] = 0.010 \) mol L⁻¹, \( k_d = 1.0 \times 10^{-5} \) s⁻¹, \( f = 0.6 \), \( k_p = 300 \) L mol⁻¹ s⁻¹ and \( k_t = 3.0 \times 10^7 \) L mol⁻¹ s⁻¹ (termination rate \( 2k_t[\mathrm{M^\bullet}]^2 \)). Consider:
- \( [\mathrm{M^\bullet}] \approx 4.5 \times 10^{-8} \) mol L⁻¹.
- \( R_p \approx 6.7 \times 10^{-5} \) mol L⁻¹ s⁻¹.
- \( X_n \approx 1100 \) if all termination is by combination.
- If the viscosity rises so that \( k_t \) falls 100-fold at the same \( [\mathrm{M}] \) and \( [\mathrm{I}] \), \( R_p \) rises 100-fold.
Which are correct?
(a) 1, 2 and 3 only (b) 1 and 2 only (c) 1, 2, 3 and 4 (d) 2 and 4 only
Answer: (a) 1, 2 and 3 only
- \( (fk_d[\mathrm{I}]/k_t)^{1/2} = (6.0 \times 10^{-8}/3.0 \times 10^7)^{1/2} = 4.47 \times 10^{-8} \). Correct.
- \( 300 \times 5.0 \times 4.47 \times 10^{-8} = 6.7 \times 10^{-5} \). Correct.
- \( \nu = 6.7 \times 10^{-5}/1.2 \times 10^{-7} = 559 \); \( X_n = 2\nu = 1118 \). Correct.
- \( R_p \propto k_t^{-1/2} \): a 100-fold fall in \( k_t \) gives a 10-fold rise. Wrong.
Practice Q6. For a monomer with illustrative \( \Delta H_p = -70 \) kJ mol⁻¹ and \( \Delta S_p^\circ = -105 \) J K⁻¹ mol⁻¹ (1 mol L⁻¹ standard state), which statements are correct?
- The ceiling temperature at 1 mol L⁻¹ monomer is about 667 K.
- Diluting the monomer to 0.1 mol L⁻¹ lowers the ceiling temperature to about 564 K.
- At 400 K the equilibrium monomer concentration is about \( 2 \times 10^{-4} \) mol L⁻¹.
- Raising the temperature above \( T_c \) increases the rate of polymerisation.
(a) 1, 2 and 3 only (b) 1 and 3 only (c) 2 and 4 only (d) 1, 2, 3 and 4
Answer: (a) 1, 2 and 3 only
- \( 70{,}000/105 = 667 \) K. Correct.
- \( -70{,}000/(-105 + 8.314\ln 0.1) = 564 \) K. Correct.
- \( \ln[\mathrm{M}]_e = -21.05 + 12.63 = -8.42 \); \( [\mathrm{M}]_e = 2.2 \times 10^{-4} \). Correct.
- Above \( T_c \), \( \Delta G_p > 0 \): net depolymerisation. Wrong.
Practice Q7. In a radical polymerisation, \( 1/X_n \) is measured at different ratios of a solvent S to monomer, with \( R_p \) held constant:
| \( [\mathrm{S}]/[\mathrm{M}] \) | 0 | 2 | 4 | 6 |
|---|---|---|---|---|
| \( 10^4/X_n \) | 8.0 | 10.0 | 12.0 | 14.0 |
Which statements are correct?
- The transfer constant to solvent \( C_S = 1.0 \times 10^{-4} \).
- Without solvent, \( X_n = 1250 \).
- At \( [\mathrm{S}]/[\mathrm{M}] = 10 \), \( X_n \approx 556 \).
- Adding S lowers \( R_p \) in proportion to \( X_n \).
(a) 1, 2 and 3 only (b) 1 and 2 only (c) 2, 3 and 4 only (d) 1, 2, 3 and 4
Answer: (a) 1, 2 and 3 only
- Slope \( = (2.0 \times 10^{-4})/2 = 1.0 \times 10^{-4} \). Correct.
- \( 1/X_n = 8.0 \times 10^{-4} \), \( X_n = 1250 \). Correct.
- \( 1/X_n = 8.0 \times 10^{-4} + 10 \times 1.0 \times 10^{-4} = 1.8 \times 10^{-3} \); \( X_n = 556 \). Correct.
- Normal chain transfer leaves \( R_p \) unchanged (the data were taken at constant \( R_p \)). Wrong.
Quick Revision Table
| Idea | Formula / fact |
|---|---|
| Initiation | \( R_i = 2fk_d[\mathrm{I}] \); \( t_{1/2} = \ln 2/k_d \) |
| Rate | \( R_p = k_p[\mathrm{M}]\,(fk_d[\mathrm{I}]/k_t)^{1/2} \) |
| Kinetic chain length | \( \nu = k_p[\mathrm{M}]/2(fk_dk_t[\mathrm{I}])^{1/2} = k_p^2[\mathrm{M}]^2/2k_tR_p \) |
| \( X_n \) | \( 2\nu \) (combination, Đ 1.5); \( \nu \) (disproportionation, Đ 2) |
| Activation energies | \( E_R = E_p + E_d/2 - E_t/2 \); \( E_{X_n} = E_p - E_d/2 - E_t/2 \) (negative) |
| Mayo | \( 1/X_n = (1/X_n)_0 + C_M + C_S[\mathrm{S}]/[\mathrm{M}] + C_I[\mathrm{I}]/[\mathrm{M}] \) |
| Gel effect | \( k_t \) falls at high viscosity; \( R_p \), \( X_n \) rise |
| Ceiling temperature | \( T_c = \Delta H_p/(\Delta S_p^\circ + R\ln[\mathrm{M}]) \) |
| Living anionic | \( R_p = k_p[\mathrm{M}][\mathrm{I}]_0 \); \( X_n = p[\mathrm{M}]_0/[\mathrm{I}]_0 \) (×2 naphthalenide); Đ ≈ 1 + 1/\( X_n \) |
| Cationic | \( R_p \propto [\mathrm{I}][\mathrm{M}]^2 \); \( 1/X_n = k_t/k_p[\mathrm{M}] + C_M \); run cold |
| Copolymer | \( F_1 = (r_1f_1^2 + f_1f_2)/(r_1f_1^2 + 2f_1f_2 + r_2f_2^2) \) |
| Azeotrope | \( f_1 = (1 - r_2)/(2 - r_1 - r_2) \) |
Key Takeaways
What’s Next
- Step-Growth Polymerisation Kinetics: the contrasting mechanism.
- Determination of Molar Masses: measuring the \( X_n \) and Đ predicted here.
- Ziegler–Natta and metallocene catalysts: Homogeneous Catalysis.
- Polymer Chemistry: Quick Revision.