Hydrological Cycle, Water Resources and Management
CSIR NET Earth Sciences: global water budget, residence time, runoff, aquifers, Darcy's law, well hydraulics, saline intrusion, water quality and management.
- 22 min
On this page · 14 sections
Prerequisites
- Unit conversions (mm of rain over an area to cubic metres, seconds in a year) and rate arithmetic from Numerical Ability.
- Water chemistry (hardness, pH, dissolved species) from Aquatic Chemistry and Water Quality.
- Basic Earth-system context (atmosphere, monsoon, oceans) from Earth, Space and Environment.
The Hook: A Hand Pump That Ran Dry
The Hydrological Cycle
The hydrological cycle is the continuous circulation of water between the oceans, atmosphere, land surface, subsurface and biosphere, driven by solar energy (evaporation) and gravity (precipitation, runoff, infiltration).
graph LR
O[Oceans] -->|evaporation| A[Atmosphere]
A -->|precipitation| O
A -->|precipitation| L[Land surface]
L -->|evapotranspiration| A
L -->|infiltration| S[Soil moisture]
S -->|percolation / recharge| G[Groundwater]
L -->|surface runoff| R[Rivers and lakes]
G -->|baseflow| R
R -->|discharge| O
G -->|submarine groundwater discharge| O
A -->|advection over land| LProcesses and terms
| Process | Meaning |
|---|---|
| Evaporation | liquid to vapour from open water and soil |
| Transpiration | water vapour lost through plant stomata |
| Evapotranspiration (ET) | evaporation plus transpiration; on land the two are usually measured together |
| Potential ET (PET) | ET when water supply is not limiting; actual ET is less than or equal to PET |
| Interception | rain caught by vegetation and evaporated before reaching the ground |
| Infiltration | entry of water into the soil surface |
| Percolation | downward movement through the unsaturated zone to the water table |
| Recharge | water reaching the saturated zone |
| Overland flow | surface runoff when rainfall intensity exceeds infiltration capacity (Hortonian) or the soil is already saturated (saturation excess) |
| Interflow | lateral flow in the unsaturated zone towards streams |
| Baseflow | groundwater discharge that keeps rivers flowing in the dry season |
| Sublimation | ice to vapour directly (glaciers, snowpack in dry air) |
Where the water is
The widely used estimate of global water storage (Shiklomanov, as tabulated by the USGS) is:
| Reservoir | Volume (km\(^3\)) | Share of all water | Share of fresh water |
|---|---|---|---|
| Oceans, seas, bays | about \( 1.338\times 10^{9} \) | about 96.5% | — |
| Ice caps, glaciers, permanent snow | about \( 2.4\times 10^{7} \) | about 1.74% | about 68.7% |
| Groundwater (fresh and saline) | about \( 2.34\times 10^{7} \) | about 1.69% | fresh groundwater about 30.1% |
| Lakes (fresh and saline) | about \( 1.8\times 10^{5} \) | about 0.013% | small |
| Soil moisture | about \( 1.65\times 10^{4} \) | about 0.001% | small |
| Atmosphere | about \( 1.29\times 10^{4} \) | about 0.001% | small |
| Rivers | about \( 2.1\times 10^{3} \) | about 0.0002% | small |
Fresh water is only about 2.5% of all water, and more than two-thirds of that is locked in ice. Of the liquid fresh water, almost all is groundwater; rivers and lakes hold a tiny fraction.
Fluxes and residence time
Global precipitation and evaporation are each roughly 500,000 km\(^3\) yr\(^{-1}\). The oceans evaporate more than they receive as rain, and the difference is carried over the continents as vapour and returns as river and groundwater discharge of roughly 40,000 km\(^3\) yr\(^{-1}\). Different compilations differ by several per cent; quote these as approximate.
For a reservoir in steady state, the mean residence time is
$$\boxed{\tau = \frac{\text{storage}}{\text{flux in (= flux out)}}}$$| Reservoir | Typical residence time |
|---|---|
| Atmosphere | about 8–10 days |
| Rivers | weeks to months |
| Soil moisture | weeks to a year |
| Large lakes | years to decades (or longer) |
| Shallow groundwater | years to centuries |
| Deep groundwater | up to tens of thousands of years |
| Oceans | a few thousand years |
| Ice sheets | up to hundreds of thousands of years |
Residence time decides how fast a pollutant is flushed out: a river recovers from a spill in weeks; a contaminated deep aquifer may stay contaminated for centuries.
The Water Balance
For any control volume (a catchment, an aquifer, a lake) over a chosen period:
$$\boxed{P = Q + ET + \Delta S}$$where \( P \) is precipitation, \( Q \) is runoff (stream discharge leaving the catchment), \( ET \) is actual evapotranspiration and \( \Delta S \) is the change in storage (soil moisture, groundwater, snow, reservoirs). Over many years \( \Delta S \approx 0 \) for an undisturbed catchment, so \( ET \approx P - Q \). If groundwater is mined, \( \Delta S \) is negative.
Express every term as a depth over the catchment (mm) or as a volume (m\(^3\)): 1 mm over 1 km\(^2\) is 1,000 m\(^3\).
Runoff and the hydrograph
A storm hydrograph plots discharge against time at a gauging station after a rainfall event.
| Feature | Meaning |
|---|---|
| Rising limb | quickflow arriving from the catchment |
| Peak discharge | maximum flow |
| Lag time | time from the centre of mass of rainfall to the peak |
| Recession (falling) limb | drainage of storage after rain stops |
| Baseflow | the groundwater-fed part beneath the quickflow |
Factors that raise the peak and shorten the lag: steep slopes, small and round catchments, impermeable rock, saturated soils, intense rain, and urbanisation (roofs, roads and storm drains). Forests, permeable soils and floodplain wetlands lower and delay the peak.
The unit hydrograph (Sherman) is the direct-runoff hydrograph from 1 unit (for example 1 cm) of effective rainfall falling uniformly over the catchment in a stated duration; by linearity it is scaled and summed to predict floods from other storms.
Infiltration
Horton’s equation describes how infiltration capacity falls during a storm as the soil wets:
$$f(t) = f_c + (f_0 - f_c)e^{-kt}$$with \( f_0 \) the initial capacity, \( f_c \) the final (steady) capacity and \( k \) a decay constant. Overland flow begins when rainfall intensity exceeds \( f(t) \).
Peak runoff: the rational method
For small catchments (a few km\(^2\)), the peak discharge is
$$\boxed{Q_p = \frac{C\,I\,A}{3.6}}$$with \( Q_p \) in m\(^3\) s\(^{-1}\), \( I \) the rainfall intensity in mm h\(^{-1}\) for a duration equal to the time of concentration, \( A \) in km\(^2\), and \( C \) the dimensionless runoff coefficient (about 0.7–0.95 for paved urban areas, about 0.1–0.3 for forest and grassland on permeable soils). For \( C = 0.6 \), \( I = 50 \) mm h\(^{-1}\) and \( A = 2 \) km\(^2\): \( Q_p = 60/3.6 \approx 16.7 \) m\(^3\) s\(^{-1}\).
Groundwater
The subsurface profile
- Unsaturated (vadose) zone: pores contain both air and water; water held by capillary and adsorptive forces at less than atmospheric pressure.
- Capillary fringe: just above the water table, nearly saturated by capillary rise.
- Water table: the surface at which pore-water pressure equals atmospheric pressure; the top of the saturated (phreatic) zone.
Porosity, specific yield and retention
Porosity \( n \) is the void fraction. Not all of it drains under gravity:
$$\boxed{n = S_y + S_r}$$where \( S_y \) is the specific yield (water released by gravity drainage per unit volume) and \( S_r \) the specific retention (water held against gravity). Clay has high porosity (often 40–60%) but very low specific yield (a few per cent) because the pores are tiny; sand and gravel have lower porosity but much higher specific yield. Porosity is not permeability.
Effective porosity \( n_e \) is the interconnected porosity available for flow.
Aquifer vocabulary
| Term | Meaning | Example |
|---|---|---|
| Aquifer | saturated formation that stores and transmits usable quantities of water | alluvial sand and gravel, karst limestone, fractured basalt |
| Aquitard | leaky, low-permeability layer; transmits water slowly | silty clay |
| Aquiclude | stores water but transmits almost none | clay, shale |
| Aquifuge | neither stores nor transmits | massive unfractured granite |
| Unconfined aquifer | bounded above by the water table | shallow alluvium |
| Confined aquifer | sandwiched between confining layers; water under pressure | deep alluvial aquifers |
| Perched aquifer | a local saturated lens above the main water table, held by a clay lens | hill slopes |
| Artesian well | well in a confined aquifer whose water rises above the aquifer top; flowing artesian if it rises above ground | — |
| Potentiometric (piezometric) surface | the level to which water would rise in wells tapping a confined aquifer | — |
Storage terms: an unconfined aquifer releases water by draining pores (storage = \( S_y \), typically 0.1–0.3). A confined aquifer stays saturated and releases water only by the expansion of water and compression of the skeleton, so its storativity \( S \) is tiny (about \( 10^{-5} \) to \( 10^{-3} \)). The same head drop yields hundreds to thousands of times less water from a confined aquifer.
In India, the main aquifer systems are the thick alluvium of the Indo-Gangetic–Brahmaputra plains (high yield, mostly unconfined above, confined at depth), the hard rocks of the peninsula (granite, gneiss, Deccan basalt) where water occurs in the weathered zone and fractures, and coastal and sedimentary aquifers.
Darcy’s law
Henry Darcy’s sand-column experiments (Dijon) gave the basic law of groundwater flow:
$$\boxed{Q = -K A \frac{dh}{dl}} \qquad q = \frac{Q}{A} = -K\,i$$- \( h \) is hydraulic head = elevation head \( z \) + pressure head \( p/\rho g \); water flows from high to low head, not necessarily from high to low pressure or elevation.
- \( i = dh/dl \) is the hydraulic gradient (dimensionless).
- \( K \) is the hydraulic conductivity (m s\(^{-1}\)); it depends on both the medium and the fluid. The medium-only property is the intrinsic permeability \( k \) (m\(^2\)): \( K = k\rho g/\mu \).
- \( q \) is the specific discharge (Darcy flux), a volume per unit total area per time.
The actual average velocity of water in the pores is faster:
$$\boxed{v = \frac{q}{n_e} = \frac{K i}{n_e}}$$Darcy’s law holds for laminar flow (Reynolds number below about 1–10). It fails in karst conduits and near high-yield wells.
| Material | Typical \( K \) (m s\(^{-1}\), order of magnitude) |
|---|---|
| Gravel | \( 10^{-3} \) to 1 |
| Clean sand | \( 10^{-6} \) to \( 10^{-2} \) |
| Silt | \( 10^{-9} \) to \( 10^{-5} \) |
| Clay (unweathered) | \( 10^{-13} \) to \( 10^{-9} \) |
| Karst limestone | \( 10^{-6} \) to \( 10^{-2} \) |
| Fractured crystalline rock | \( 10^{-8} \) to \( 10^{-4} \) |
| Unfractured crystalline rock | below \( 10^{-10} \) |
Transmissivity \( T = Kb \) (m\(^2\) day\(^{-1}\)) is the rate at which water passes through the full saturated thickness \( b \) of an aquifer under unit gradient.
Well hydraulics
Pumping lowers the head around a well into a cone of depression; drawdown \( s \) is the fall in head. For steady radial flow in a confined aquifer (Thiem equation):
$$\boxed{Q = \frac{2\pi T\,(s_1 - s_2)}{\ln(r_2/r_1)}}$$where \( s_1, s_2 \) are drawdowns in observation wells at distances \( r_1 < r_2 \). A pumping test with two observation wells therefore gives \( T \), and \( K = T/b \). For non-steady flow the Theis solution (and the Cooper–Jacob straight-line approximation) also yields storativity.
Overlapping cones from many wells cause well interference, regional decline of the water table, drying of shallow wells and springs, loss of baseflow to rivers, and land subsidence where compressible clays compact as heads fall (subsidence is largely irreversible because the clay does not re-expand).
Saline intrusion: the Ghyben–Herzberg relation
In a coastal unconfined aquifer fresh water floats on denser seawater. Hydrostatic balance gives the depth \( z \) of the fresh–salt interface below sea level for a water table at height \( h \) above sea level:
$$\boxed{z = \frac{\rho_f}{\rho_s - \rho_f}\,h \approx 40\,h}$$with \( \rho_f = 1.000 \) and \( \rho_s = 1.025 \) g cm\(^{-3}\). Lowering the water table by 1 m near the coast lets the interface rise by about 40 m: coastal over-pumping draws seawater into wells. Remedies: reduce pumping, artificial recharge, injection barriers, and spreading wells inland.
Water Quality in Brief
| Problem | Typical cause | Indian setting (examples) |
|---|---|---|
| Arsenic | release from iron oxyhydroxides under reducing conditions in young alluvial sediments | Ganga–Brahmaputra delta and plains (West Bengal and neighbouring states) |
| Fluoride | weathering of fluoride-bearing minerals (fluorite, apatite, micas, amphiboles) in hard-rock and arid aquifers | parts of Rajasthan, Telangana, Andhra Pradesh, Karnataka and others |
| Salinity | seawater intrusion, evaporative concentration, inherent connate water | coastal Gujarat (Saurashtra, Kutch), arid north-west |
| Nitrate | fertilisers, sewage, animal waste | intensively farmed plains |
| Hardness | dissolved Ca\(^{2+}\) and Mg\(^{2+}\) (carbonate rocks) | widespread |
| Pathogens, BOD | untreated sewage | urban rivers |
WHO guideline values often quoted: arsenic 10 μg L\(^{-1}\), fluoride 1.5 mg L\(^{-1}\), nitrate 50 mg L\(^{-1}\) (as NO\(_3^-\)). The Indian drinking-water standard is IS 10500 (BIS). Chemistry of these species is covered in Aquatic Chemistry and Water Quality.
Water Resources and Management
Scarcity indicators
The Falkenmark indicator classifies a region by renewable fresh water per person per year: below 1,700 m\(^3\) is water stress, below 1,000 m\(^3\) is water scarcity, and below 500 m\(^3\) is absolute scarcity. India’s per-capita availability has fallen with population growth and is in the stressed range in national averages; many basins are far worse.
In groundwater assessments, the Central Ground Water Board (CGWB) uses the stage of groundwater extraction:
$$\text{Stage (\%)} = \frac{\text{annual groundwater extraction}}{\text{annual extractable groundwater resource}}\times 100$$| Category | Stage of extraction |
|---|---|
| Safe | up to 70% |
| Semi-critical | above 70% up to 90% |
| Critical | above 90% up to 100% |
| Over-exploited | above 100% |
(Units with saline groundwater are classed separately.) Over-exploited blocks are concentrated in the north-west (Punjab, Haryana, Rajasthan, Delhi) and in hard-rock parts of the south.
Management tools
| Approach | What it does |
|---|---|
| Integrated Water Resources Management (IWRM) | manages surface water, groundwater, land and ecosystems together, by river basin |
| Watershed management | treats a catchment from ridge to valley: contour bunds, terraces, gully plugs, check dams, afforestation; slows runoff, raises infiltration and reduces erosion |
| Rainwater harvesting | rooftop or surface collection, stored or diverted to recharge |
| Artificial / managed aquifer recharge | percolation tanks, recharge wells and shafts, spreading basins, injection wells |
| Conjunctive use | uses canal water in wet years and groundwater in dry years; also controls waterlogging in canal commands |
| Demand management | drip and sprinkler irrigation, crop choice, metering and pricing, leak control |
| Reuse and new sources | treated wastewater for industry and irrigation; desalination for coastal cities |
| Storage and transfer | dams and reservoirs; inter-basin transfers (national river-linking plan) |
| Groundwater governance | participatory aquifer management, regulation of new wells, aquifer mapping |
Canal irrigation without drainage raises the water table, leading to waterlogging and salinisation (capillary rise and evaporation concentrate salts at the surface). Conjunctive use and sub-surface drainage control it.
Tracing water: isotopes
Stable isotopes of water (\( \delta^{18}\text{O} \), \( \delta\text{D} \)) identify sources of recharge (rain at high altitude or in cold seasons is isotopically lighter), mixing between rivers and aquifers, and evaporation (enrichment off the meteoric water line). Tritium (half-life about 12.3 yr) marks water recharged since the 1950s bomb tests, and \( ^{14}\text{C} \) dates old groundwater. Radiometric principles are in Geological Time Scale and Radiometric Dating.
Memory Tricks
Don’t Confuse
| This | vs | That |
|---|---|---|
| Porosity: how much void space | Permeability / hydraulic conductivity: how easily water moves through it | |
| Specific discharge \( q = Ki \) | Seepage (average linear) velocity \( v = Ki/n_e \) | |
| Hydraulic conductivity \( K \) (m s\(^{-1}\), depends on fluid) | Intrinsic permeability \( k \) (m\(^2\), rock only) | |
| Specific yield (unconfined, 0.1–0.3) | Storativity (confined, \( 10^{-5} \)–\( 10^{-3} \)) | |
| Water table (unconfined) | Potentiometric surface (confined) | |
| Aquitard: leaks slowly | Aquiclude: practically no flow | |
| Infiltration: entry at the surface | Percolation: movement down through the vadose zone | |
| Hortonian overland flow: rain faster than infiltration | Saturation-excess flow: soil already full |
Common Mistakes
Practice
All questions below are original practice questions written for this page. They are not from any CSIR NET paper.
Level 1: Foundation
- Which reservoir holds most of Earth’s liquid fresh water?
- Write the relation between porosity, specific yield and specific retention.
- What is the mean residence time of water vapour in the atmosphere, roughly?
Answers
- Groundwater. Ice holds more fresh water overall, but it is not liquid; rivers and lakes hold far less than groundwater.
- \( n = S_y + S_r \).
- About 8–10 days (storage about 12,900 km\(^3\) divided by about 500,000 km\(^3\) yr\(^{-1}\)).
Level 2: Part B Style
Practice Q1. An unconfined aquifer has porosity 0.30 and specific retention 0.08. Over an area of 2 km\(^2\) the water table falls by 3 m during a dry season. The volume of water released from storage is:
(a) \( 4.8\times 10^{5} \) m\(^3\) (b) \( 1.32\times 10^{6} \) m\(^3\) (c) \( 1.80\times 10^{6} \) m\(^3\) (d) \( 6.0\times 10^{6} \) m\(^3\)
Answer: (b)
\( S_y = 0.30 - 0.08 = 0.22 \). Volume \( = A\,\Delta h\,S_y = 2\times 10^{6}\times 3\times 0.22 = 1.32\times 10^{6} \) m\(^3\).
(c) uses the full porosity; (a) uses the specific retention; (d) is the rock volume.
Practice Q2. On a coastal island the water table stands 2.0 m above sea level. Heavy pumping lowers it to 1.5 m. According to the Ghyben–Herzberg relation (\( \rho_s = 1.025 \) g cm\(^{-3}\)), the fresh–salt interface:
(a) rises by 0.5 m (b) rises by 20 m (c) falls by 20 m (d) rises by 60 m
Answer: (b) rises by 20 m
\( z = 40h \): from \( 40\times 2.0 = 80 \) m to \( 40\times 1.5 = 60 \) m below sea level, so the interface rises by 20 m. (d) is the new depth, not the change.
Practice Q3. A well tapping a confined aquifer flows at the surface without pumping. This happens because:
(a) the water table lies above the ground surface (b) the potentiometric surface of the aquifer lies above the ground surface at the well (c) the aquifer has a high specific yield (d) capillary rise lifts water above the aquifer
Answer: (b)
A confined aquifer has no water table of its own; its head is described by the potentiometric surface. Where this surface is above ground the well is a flowing artesian well.
Practice Q4. A lake of volume 2 km\(^3\) has a steady outflow of 0.5 km\(^3\) yr\(^{-1}\) and negligible evaporation. A conservative pollutant is spilled once. The time scale on which its concentration falls is set by a residence time of:
(a) 0.25 yr (b) 2.5 yr (c) 4 yr (d) 10 yr
Answer: (c) 4 yr
\( \tau = V/Q = 2/0.5 = 4 \) yr. For a well-mixed lake the concentration falls as \( e^{-t/\tau} \), to about 37% after 4 years.
Level 3: Part C Style
Practice Q5. A well fully penetrating a confined aquifer 25 m thick is pumped at a steady 1,500 m\(^3\) day\(^{-1}\). At equilibrium, drawdowns are:
| Observation well | Distance from pumping well (m) | Drawdown (m) |
|---|---|---|
| OW-1 | 20 | 2.4 |
| OW-2 | 80 | 1.2 |
The transmissivity and hydraulic conductivity of the aquifer are closest to:
(a) 276 m\(^2\) day\(^{-1}\), 11 m day\(^{-1}\) (b) 199 m\(^2\) day\(^{-1}\), 8 m day\(^{-1}\) (c) 552 m\(^2\) day\(^{-1}\), 22 m day\(^{-1}\) (d) 276 m\(^2\) day\(^{-1}\), 6900 m day\(^{-1}\)
Answer: (a)
Thiem: \( T = \frac{Q\ln(r_2/r_1)}{2\pi(s_1 - s_2)} = \frac{1500\times\ln 4}{2\pi\times 1.2} = \frac{1500\times 1.386}{7.540} \approx 276 \) m\(^2\) day\(^{-1}\).
\( K = T/b = 276/25 \approx 11 \) m day\(^{-1}\) (about \( 1.3\times 10^{-4} \) m s\(^{-1}\), a clean sand).
(c) forgets the 2 in \( 2\pi \) (it uses \( \pi \)); (d) multiplies by the thickness instead of dividing.
Practice Q6. Consider these statements:
- Urbanisation of a catchment usually increases peak discharge and shortens lag time.
- A confined aquifer releases more water per metre of head decline than an unconfined aquifer of the same area.
- Groundwater always flows from points of higher elevation to points of lower elevation.
- Baseflow sustains river discharge in the dry season.
Which are correct?
(a) 1 and 4 only (b) 1, 2 and 4 only (c) 2 and 3 only (d) 1, 3 and 4 only
Answer: (a) 1 and 4 only
- 1 true: impervious surfaces and drains reduce infiltration and speed up runoff.
- 2 false: storativity of a confined aquifer (about \( 10^{-5} \)–\( 10^{-3} \)) is far smaller than the specific yield of an unconfined one (0.1–0.3).
- 3 false: flow follows total head; in discharge zones water moves upward.
- 4 true: dry-season flow in perennial rivers is groundwater discharge.
Practice Q7. For a 1,000 km\(^2\) catchment over one year: rainfall 900 mm; mean discharge at the outlet 8.0 m\(^3\) s\(^{-1}\); the regional water table fell by 0.5 m in an unconfined aquifer of specific yield 0.10; other storage changes are negligible. Actual evapotranspiration is closest to:
(a) 548 mm (b) 598 mm (c) 648 mm (d) 698 mm
Answer: (d) 698 mm
Runoff depth: \( 8.0\times 365\times 86{,}400 = 2.52\times 10^{8} \) m\(^3\); divided by \( 10^{9} \) m\(^2\) gives 0.252 m = 252 mm.
Storage change: \( \Delta S = -0.5\times 0.10 = -0.05 \) m = \( -50 \) mm (storage was lost).
\( ET = P - Q - \Delta S = 900 - 252 - (-50) = 698 \) mm.
(c) ignores the storage change; (b) subtracts it with the wrong sign (\( 900 - 252 - 50 \)). Groundwater mining lets ET plus runoff exceed what rain alone could supply.
Quick Revision Table
| Idea | Fact or formula |
|---|---|
| Global water | oceans about 96.5%; ice about 1.74%; groundwater about 1.69%; fresh water about 2.5% |
| Fresh water | about 69% ice, about 30% groundwater, rest surface |
| Global P (= E) | about 500,000 km\(^3\) yr\(^{-1}\); land-to-ocean runoff about 40,000 km\(^3\) yr\(^{-1}\) |
| Residence time | \( \tau = \) storage / flux; atmosphere about 9 days; oceans a few thousand years |
| Water balance | \( P = Q + ET + \Delta S \); 1 mm over 1 km\(^2\) = 1,000 m\(^3\) |
| Rational method | \( Q_p = CIA/3.6 \) (mm h\(^{-1}\), km\(^2\), m\(^3\) s\(^{-1}\)) |
| Horton infiltration | \( f = f_c + (f_0 - f_c)e^{-kt} \) |
| Porosity | \( n = S_y + S_r \) |
| Darcy | \( Q = KA\,i \); \( v = Ki/n_e \); \( K = k\rho g/\mu \) |
| Transmissivity | \( T = Kb \) |
| Thiem (confined) | \( Q = 2\pi T(s_1 - s_2)/\ln(r_2/r_1) \) |
| Ghyben–Herzberg | \( z \approx 40h \) |
| Storage | \( S_y \) 0.1–0.3 (unconfined); \( S \) \( 10^{-5} \)–\( 10^{-3} \) (confined) |
| Falkenmark | stress < 1,700; scarcity < 1,000; absolute < 500 m\(^3\) per person per year |
| CGWB categories | safe ≤ 70%; semi-critical 70–90%; critical 90–100%; over-exploited > 100% |
| Quality | As (delta alluvium), F (hard rock, arid), salinity (coast), nitrate (farms) |
Key Takeaways
What’s Next
- Energy Resources and the Environmental Impact of Energy and Land Use: hydropower, the energy mix and how land use changes runoff and erosion.
- Natural Hazards: floods, droughts and return periods build on this page.
- Environmental Earth Sciences: Quick Revision: the whole chapter on one page.
- Back to the chapter overview.