Skip to content

Mineral Resource Exploitation and Conservation

CSIR NET Earth Sciences: ores, grade and cut-off, resources vs reserves, ore-forming processes, mining and beneficiation, acid mine drainage, conservation.

  • 17 min read
  • Updated
On this page · 17 sections
  1. Prerequisites
  2. The Hook: Gold Below, Waste Above
  3. Basic Vocabulary
  4. Resources and Reserves
  5. How Ores Form
  6. Finding Ore: Exploration
  7. Getting It Out: Mining Methods
  8. Processing: Beneficiation and Extraction
  9. Environmental Impact of Mining
  10. Conservation of Mineral Resources
  11. Memory Tricks
  12. Don’t Confuse
  13. Common Mistakes
  14. Practice
  15. Quick Revision Table
  16. Key Takeaways
  17. What’s Next

Prerequisites

The Hook: Gold Below, Waste Above

Basic Vocabulary

TermMeaning
Mineral deposita concentration of a mineral or element well above its crustal average
Orematerial from which a metal or mineral can be extracted at a profit
Ore mineralthe valuable mineral (chalcopyrite, galena, hematite)
Ganguethe worthless minerals in an ore (quartz, calcite, feldspar)
Gradeconcentration of the valuable component (% for base metals, g t\(^{-1}\) for gold)
Tonnagequantity of ore; tonnage × grade = contained metal
Cut-off gradethe lowest grade that can be mined and processed without loss
Overburdenrock and soil above an ore body that must be removed in surface mining
Tailingsfinely ground waste left after processing

Concentration factor

$$\boxed{\text{Concentration factor} = \frac{\text{minimum economic ore grade}}{\text{average crustal abundance}}}$$

Taking illustrative crustal averages (estimates differ between compilations):

ElementCrustal average (taken as)Typical ore gradeConcentration factor
Aluminiumabout 8%about 32% Al (bauxite)about 4
Ironabout 5%about 60% Feabout 12
Copperabout 0.006% (60 ppm)about 0.6%about 100
Goldabout 0.004 g t\(^{-1}\)about 4 g t\(^{-1}\)about 1,000

Abundant elements (Al, Fe) need little natural enrichment; scarce elements (Cu, Au, Pb, Zn) need large enrichment, which only special geological processes achieve. That is why scarce metals are found in few places.

Resources and Reserves

The McKelvey diagram classifies mineral occurrences along two axes: geological certainty (how well known) and economic feasibility (whether profitable).

Identified: measuredIdentified: indicatedIdentified: inferredUndiscovered: hypothetical, speculative
EconomicReserve (proved)Reserve (probable)inferred reserveundiscovered resource
Marginally economicmarginal reservemarginal reserve——
Sub-economicsub-economic resourcesub-economic resource——
  • A resource is any concentration of potential economic interest, known or estimated.
  • A reserve is the part of an identified resource that can be extracted profitably now with existing technology.
  • Reserves change without any geological change: a rise in metal price or a better process converts resources to reserves; a price fall does the reverse.
  • India reports its mineral inventory under the United Nations Framework Classification (UNFC), which codes economic viability (E), feasibility (F) and geological knowledge (G).

How long will it last?

Static lifetime = reserves / current annual production. If consumption grows at rate \( r \) per year, the exponential lifetime is

$$\boxed{T = \frac{1}{r}\ln\left(1 + \frac{rR}{P_0}\right)}$$

where \( R \) is the reserve and \( P_0 \) the present production. With \( R = 800 \) Mt and \( P_0 = 20 \) Mt yr\(^{-1}\), the static lifetime is 40 yr, but at 3% growth it is \( \ln(2.2)/0.03 \approx 26 \) yr. Growth shortens lifetimes sharply. In practice reserves are also replenished by exploration and price changes, so neither number is a forecast.

Hubbert’s peak. Production of a finite resource in a region tends to rise, peak and decline in a roughly bell-shaped curve, with the peak near the point where about half the ultimately recoverable resource has been produced. M. King Hubbert used this in 1956 to forecast the peak of United States oil production around 1970.

How Ores Form

ProcessMechanismExamples (deposit type)Indian examples
Magmaticcrystal settling and immiscible sulphide liquids in mafic–ultramafic magmachromite, PGE, Ni–Cu sulphides, diamond (kimberlite)chromite of the Sukinda valley (Odisha); diamonds at Panna (Madhya Pradesh)
Pegmatiticlate, volatile-rich granite meltsmica, Li, Be, Ta, Nb, feldsparmica of Koderma (Jharkhand) and Nellore (Andhra Pradesh)
Hydrothermalhot aqueous fluids leach, carry and precipitate metals in veins, stockworks and replacementsporphyry Cu–Mo, lode gold, Pb–Zn, Sn–Wcopper at Malanjkhand (Madhya Pradesh) and Khetri (Rajasthan); gold at Kolar and Hutti (Karnataka)
Sedimentary exhalative and sediment-hostedmetal-bearing brines vented or circulated in sedimentary basinsPb–ZnZawar and Rampura–Agucha (Rajasthan)
Volcanogenic massive sulphide (VMS)sea-floor hydrothermal vents (black smokers)Cu–Zn–Pb—
Chemical sedimentaryprecipitation from sea waterbanded iron formations, Mn, phosphorite, evaporitesiron ore of Bailadila (Chhattisgarh), Singhbhum–Keonjhar (Jharkhand–Odisha), Bellary–Hospet (Karnataka); phosphorite of Jhamarkotra (Rajasthan)
Residual (weathering)intense tropical weathering removes soluble elements and leaves insoluble Al, Fe, Nibauxite, laterite, Ni-lateriteEast Coast bauxite (Panchpatmali, Koraput, Odisha)
Supergene enrichmentmetals leached from the oxidised upper part of a sulphide body are re-precipitated just below the water tableenriched Cu sulphide blanket—
Placerheavy, resistant minerals concentrated by moving water or windgold, cassiterite, ilmenite, rutile, zircon, monazite, garnet, sillimanitebeach sands of Chavara (Kerala), Manavalakurichi (Tamil Nadu), Chhatrapur (Odisha)
Metamorphicrecrystallisation during metamorphismgraphite, sillimanite, kyanite, garnet—

Manganese ores of the Balaghat–Nagpur–Bhandara belt (Madhya Pradesh–Maharashtra) and of Odisha are other important Indian deposits.

Supergene profile

From top to bottom: gossan (iron oxide cap, “iron hat”, a prospecting guide), leached (oxidised) zone, supergene enriched zone at and below the water table (Cu grade raised several-fold), and primary (hypogene) ore. The enrichment happens because Cu leached above is re-precipitated by replacing less noble metals in sulphides below.

Finding Ore: Exploration

graph LR
    A[Regional: geological maps, remote sensing, airborne geophysics] --> B[Target: geochemical anomalies, ground geophysics]
    B --> C[Drilling and sampling]
    C --> D[Resource estimation]
    D --> E[Feasibility study]
    E --> F[Mine development]
MethodWhat it detectsGood for
Geological mapping, structural analysishost rocks, alteration, controlsall deposits
Remote sensinghydrothermal alteration minerals (clays, iron oxides) by spectral signature; lineamentsporphyry and epithermal targets (see Remote Sensing)
Geochemicalanomalies in soil, stream sediment, rock, water, plantsdispersed metal haloes around ore
Magneticmagnetic susceptibilitymagnetite-rich iron ore, BIF, kimberlite pipes
Gravitydensity contrastchromite, massive sulphides, salt domes
Electrical and electromagneticconductivitymassive sulphides, graphite
Induced polarisation (IP)chargeabilitydisseminated sulphides (porphyry Cu)
Radiometric (gamma-ray)K, U, Thuranium, thorium, mapping granites

Getting It Out: Mining Methods

MethodWhen usedNotes
Open-pit (opencast)large, near-surface, lower-grade bodiescheaper per tonne; large waste and land use
Strip miningflat-lying coal, phosphateoverburden cast aside in strips; enables backfilling
Quarryingbuilding stone, limestone—
Placer and dredgingbeach and river sands—
Underground (room and pillar, cut and fill, stoping, block caving)deep or high-grade bodieshigher cost; subsidence risk; less surface disturbance
Solution mining, in-situ leachinguranium, salt, potashfluids injected and pumped out; groundwater risk
Heap leachinglow-grade gold and coppercrushed ore leached on lined pads (cyanide, acid)

Stripping ratio = waste (overburden) removed / ore mined, in tonnes or volume. A pit is extended until the break-even stripping ratio is reached:

$$\text{BESR} = \frac{\text{value of ore per tonne} - \text{cost of mining and processing the ore per tonne}}{\text{cost of removing a tonne of waste}}$$

For ore worth ₹3,000 per tonne, ore costs ₹1,800 per tonne and waste removal ₹200 per tonne: BESR \( = 1{,}200/200 = 6 \).

Cut-off grade

At the break-even cut-off grade, the value of recovered metal just covers the cost:

$$\boxed{g_c = \frac{\text{cost per tonne of ore}}{\text{metal price per tonne}\times\text{recovery}}}$$

For costs of ₹1,500 per tonne of ore, copper at ₹6,00,000 per tonne and 90% recovery: \( g_c = 1500/(600000\times 0.9) = 0.0028 \), i.e. about 0.28% Cu. Raising the price or recovery lowers the cut-off and increases reserves.

Processing: Beneficiation and Extraction

Beneficiation (mineral dressing) raises grade before smelting: crushing and grinding to free (liberate) ore minerals, then separation by physical properties.

SeparationProperty usedExamples
Gravity (jigs, spirals, shaking tables)densityheavy minerals of beach sands, gold, cassiterite, chromite
Magneticmagnetic susceptibilitymagnetite, ilmenite, garnet
Electrostatic (high-tension)electrical conductivityseparates conducting ilmenite and rutile from non-conducting zircon and monazite
Froth flotationsurface hydrophobicity (made selective by collector chemicals)sulphide ores of Cu, Pb, Zn
Leaching (hydrometallurgy)solubilitygold by cyanide; copper by sulphuric acid; bauxite by NaOH (Bayer process, leaving red mud)

Mass balance

For feed grade \( f \), concentrate grade \( c \) and tailings grade \( t \), the two-product formula gives

$$\boxed{\frac{C}{F} = \frac{f - t}{c - t}} \qquad \boxed{\text{Recovery} = \frac{c\,(f - t)}{f\,(c - t)}}$$

Environmental Impact of Mining

ImpactCause
Land degradation and deforestationopencast pits, overburden dumps, roads
Acid mine drainage (AMD)oxidation of pyrite and other sulphides in waste and workings
Heavy-metal contaminationAs, Cd, Pb, Hg, Zn released from sulphides, tailings and processing (cyanide, mercury in artisanal gold mining)
Tailings dam failureliquefaction or overtopping of slurry dams (catastrophic failures in Brazil in 2015 and 2019 are cited worldwide)
Groundwater loweringmine dewatering
Subsidencecollapse over underground workings
Dust and air pollutionblasting, haulage, crushing; silicosis in workers
Noise and vibrationblasting
Social impactdisplacement, loss of forest livelihoods
Radiologicaluranium tailings (radon, radium)

Acid mine drainage chemistry

$$\text{FeS}_2 + \tfrac{7}{2}\text{O}_2 + \text{H}_2\text{O} \rightarrow \text{Fe}^{2+} + 2\text{SO}_4^{2-} + 2\text{H}^+$$$$\text{Fe}^{2+} + \tfrac{1}{4}\text{O}_2 + \text{H}^+ \rightarrow \text{Fe}^{3+} + \tfrac{1}{2}\text{H}_2\text{O} \quad \text{(rate-limiting; bacterially catalysed at low pH)}$$$$\text{FeS}_2 + 14\,\text{Fe}^{3+} + 8\,\text{H}_2\text{O} \rightarrow 15\,\text{Fe}^{2+} + 2\text{SO}_4^{2-} + 16\,\text{H}^+$$$$\text{Fe}^{3+} + 3\text{H}_2\text{O} \rightarrow \text{Fe(OH)}_3\downarrow + 3\text{H}^+ \quad \text{("yellow boy")}$$

Overall: \( \text{FeS}_2 + \tfrac{15}{4}\text{O}_2 + \tfrac{7}{2}\text{H}_2\text{O} \rightarrow \text{Fe(OH)}_3 + 2\text{SO}_4^{2-} + 4\text{H}^+ \): each pyrite produces the equivalent of two H\(_2\)SO\(_4\). Iron-oxidising bacteria (such as Acidithiobacillus ferrooxidans) speed the ferrous-to-ferric step by orders of magnitude, so once acid conditions develop the reaction becomes self-sustaining. Low pH then dissolves heavy metals.

Acid–base accounting (ABA) predicts whether waste rock will generate acid:

$$\text{MPA (kg CaCO}_3\text{ t}^{-1}) = 31.25\times\%\text{S} \qquad \text{NNP} = \text{NP} - \text{MPA} \qquad \text{NPR} = \text{NP}/\text{MPA}$$

where MPA is the maximum potential acidity and NP the neutralisation potential (from carbonates). The factor 31.25 comes from 1% S per tonne = 10 kg S = 0.3125 kmol (with S = 32), each needing one mole of CaCO\(_3\) (100 g mol\(^{-1}\)). Commonly used screening: NPR below 1 (or NNP below about \( -20 \)) is likely acid-generating; NPR above about 2 is unlikely; in between is uncertain and needs kinetic testing.

Control and remediation: keep sulphides away from oxygen and water (submerge, cover, seal), blend with limestone, divert clean water, treat drainage with lime (active treatment), or with anoxic limestone drains and constructed wetlands (passive treatment).

Reclamation

Progressive backfilling of pits, saving and replacing topsoil, contouring dumps, revegetation with native species, phytoremediation and metal-tolerant plants, conversion of pits to water bodies, and a mine closure plan with financial assurance before mining begins.

Conservation of Mineral Resources

Minerals are non-renewable on human time scales; conservation means using them more slowly and more completely.

ApproachExamples
Reducelighter designs, longer-lasting products
Reuse and recyclescrap steel, aluminium cans (recycled aluminium needs only a small fraction of the energy of primary metal), copper wire, lead batteries; urban mining of e-waste for gold, copper and rare earths
Substitutionoptical fibre for copper cable, plastics and composites for metals, LED for mercury lamps
Better extractionhigher recovery, selective mining, reprocessing old tailings, recovering by-products (Cd and In from zinc, Se and Te from copper, Ga from bauxite)
Waste utilisationfly ash in cement and bricks, red mud, slag in roads
Exploration and technologynew deposits, deeper and lower-grade ores, offshore resources (polymetallic nodules)
Policystockpiles of strategic minerals, efficient allocation, sustainable mining codes

Indian framework. The Mines and Minerals (Development and Regulation) Act, 1957 is the main law. Its 2015 amendment made auction the route for granting mineral concessions and created District Mineral Foundations (funds for people in mining-affected areas) and the National Mineral Exploration Trust. The National Mineral Policy, 2019 sets the policy direction. In 2023 India identified a list of critical minerals (including lithium, cobalt, graphite and rare earth elements) needed for clean energy and electronics.

Memory Tricks

Don’t Confuse

ThisvsThat
Resource: all known plus estimated, economic or notReserve: identified and profitable now
Grade: concentration in oreRecovery: fraction of metal captured by processing
Ore mineral (chalcopyrite)Gangue (quartz, calcite)
Residual deposit: leftover after weathering (bauxite)Supergene enrichment: leached then re-precipitated below (Cu blanket)
Placer: mechanical concentrationChemical sedimentary: precipitation (BIF, phosphorite)
Static lifetime: \( R/P \)Exponential lifetime: \( \frac{1}{r}\ln(1 + rR/P) \)
Magnetic survey: magnetite, kimberliteIP survey: disseminated sulphides

Common Mistakes

Practice

All questions below are original practice questions written for this page. They are not from any CSIR NET paper.

Level 1: Foundation

  1. Define a mineral reserve.
  2. Name the process that forms bauxite.
  3. Which geophysical method is most suited to detecting disseminated sulphides?
Answers
  1. The part of an identified mineral resource that can be extracted profitably under current economic and technological conditions.
  2. Residual weathering (laterisation) in a hot, humid climate.
  3. Induced polarisation (IP).

Level 2: Part B Style

Practice Q1. Taking the average crustal abundance of copper as 60 ppm and the minimum economic ore grade as 0.6% Cu, the concentration factor is:

(a) 10 (b) 100 (c) 1,000 (d) 10,000

Answer: (b) 100

60 ppm = 0.006%. \( 0.6/0.006 = 100 \). The distractors come from unit slips: treating ppm as \( 10^{-5} \) gives 10 (a); treating it as \( 10^{-7} \) or \( 10^{-8} \) gives 1,000 (c) or 10,000 (d), instead of \( 10^{-6} \).

Practice Q2. Ilmenite, rutile, zircon, monazite and garnet in the beach sands of Kerala form a deposit of which type?

(a) Residual (b) Placer (c) Hydrothermal (d) Supergene

Answer: (b) Placer

They are dense, chemically and mechanically resistant minerals concentrated by waves and currents.

Practice Q3. In the McKelvey classification, a deposit that has been drilled and measured but cannot be mined at a profit at current prices is a:

(a) reserve (b) sub-economic (or marginal) identified resource (c) hypothetical resource (d) speculative resource

Answer: (b)

It is identified (geologically certain) but not economic. Hypothetical and speculative resources are undiscovered.

Practice Q4. A copper mine’s costs are ₹1,500 per tonne of ore, recovery is 90% and copper sells at ₹6,00,000 per tonne. The break-even cut-off grade is closest to:

(a) 0.25% Cu (b) 0.28% Cu (c) 0.36% Cu (d) 2.8% Cu

Answer: (b) 0.28% Cu

\( g_c = 1500/(600000\times 0.9) = 0.00278 = 0.278\% \). (a) ignores recovery; (d) is off by a factor of ten.

Level 3: Part C Style

Practice Q5. Acid–base accounting on three waste-rock samples:

SampleTotal S (%)NP (kg CaCO\(_3\) t\(^{-1}\))
P0.540
Q2.025
R1.245

Using MPA = 31.25 × %S and the screening rule (NPR below 1 likely acid-generating, above 2 unlikely, 1–2 uncertain), which statement is correct?

(a) Only P is likely to generate acid (b) Q is likely acid-generating, P is unlikely, R is uncertain (c) All three are unlikely to generate acid because each has positive NP (d) R is the most acid-generating because it has the highest NP

Answer: (b)
SampleMPANNP = NP − MPANPR = NP/MPA
P15.6+24.42.56 (unlikely)
Q62.5−37.50.40 (likely acid)
R37.5+7.51.20 (uncertain)

What matters is the balance between acid potential and neutralising potential, not NP alone. R needs kinetic (column) testing.

Practice Q6. A lead–zinc concentrator treats ore with feed grade 1.2% Zn and produces a concentrate of 24% Zn and tailings of 0.12% Zn. Which statements are correct?

  1. About 45 kg of concentrate is produced per tonne of ore.
  2. The zinc recovery is about 90%.
  3. The enrichment ratio is 20.
  4. The recovery is \( c/f = 20 \) per cent.

(a) 1, 2 and 3 only (b) 1 and 4 only (c) 2 and 3 only (d) 1, 2, 3 and 4

Answer: (a) 1, 2 and 3 only

\( C/F = (1.2 - 0.12)/(24 - 0.12) = 0.0452 \) → 45.2 kg t\(^{-1}\) (statement 1 true).

Recovery \( = 24\times 1.08/(1.2\times 23.88) = 0.905 \) (statement 2 true).

Enrichment ratio \( c/f = 24/1.2 = 20 \) (statement 3 true); statement 4 confuses enrichment ratio with recovery.

Practice Q7. A country has an iron-ore reserve of 800 Mt and produces 20 Mt per year. Which pair gives the static lifetime and the lifetime if production grows by 3% per year?

(a) 40 yr and 26 yr (b) 40 yr and 40 yr (c) 40 yr and 53 yr (d) 26 yr and 40 yr

Answer: (a)

Static: \( 800/20 = 40 \) yr.

Exponential: \( T = \frac{1}{0.03}\ln(1 + 0.03\times 40) = \frac{\ln 2.2}{0.03} = \frac{0.788}{0.03} \approx 26.3 \) yr.

Growth always shortens the lifetime, so (c) is impossible; (d) reverses the two.

Quick Revision Table

IdeaFact or formula
Oremineral material extractable at a profit; ore mineral + gangue
Concentration factorore grade / crustal average (Al about 4, Fe about 12, Cu about 100, Au about 1,000)
Resource vs reserveMcKelvey: certainty (measured, indicated, inferred; undiscovered) × economics
IndiaUNFC classification; MMDR Act 1957 (2015: auctions, DMF, NMET); National Mineral Policy 2019; critical minerals list 2023
Lifetimestatic \( R/P \); exponential \( \frac{1}{r}\ln(1 + rR/P) \)
Hubbertbell curve; peak near half of ultimate recovery
Ore processesmagmatic, pegmatitic, hydrothermal, SEDEX, VMS, chemical sedimentary, residual, supergene, placer, metamorphic
Indian exampleschromite Sukinda; Cu Malanjkhand, Khetri; Pb–Zn Zawar, Rampura–Agucha; Fe Bailadila, Singhbhum–Keonjhar, Bellary; bauxite Panchpatmali; Au Kolar, Hutti; placers Chavara; diamond Panna
Explorationmagnetic (magnetite), gravity (dense ores), EM (massive sulphide), IP (disseminated sulphide), radiometric (U, Th, K)
Stripping ratiowaste / ore; BESR = (ore value − ore cost)/waste cost
Cut-off gradecost / (price × recovery)
Two-product\( C/F = (f - t)/(c - t) \); recovery \( = c(f - t)/[f(c - t)] \)
AMDFeS\(_2\) → 2 H\(_2\)SO\(_4\) equivalent; Fe\(^{2+}\) → Fe\(^{3+}\) rate-limiting, bacteria catalyse
ABAMPA = 31.25 × %S; NPR < 1 acid likely, > 2 unlikely
Conservationreduce, reuse, recycle, substitute, recover by-products, reprocess tailings

Key Takeaways

What’s Next

Advertisement
Advertisement