Maxwell's Equations in Geophysics
CSIR NET Earth Sciences Part C: Maxwell's equations, constitutive relations, boundary conditions, diffusion vs wave regime, skin depth, MT and GPR basics.
- 17 min
On this page · 16 sections
- Prerequisites
- The Hook: Listening to Lightning and the Sun
- The Four Equations
- Boundary Conditions
- The Static Limit: DC Resistivity
- Time-Varying Fields: Diffusion or Waves
- Skin Depth
- Magnetotellurics
- The Wave Regime: Ground-Penetrating Radar
- Memory Tricks
- Don’t Confuse
- Common Mistakes
- Practice
- Quick Revision Table
- Key Takeaways
- What’s Next
Prerequisites
- Newtonian Potential, Laplace and Poisson Equations: scalar potentials and Laplace’s equation, which return here as the static limit.
- Green’s Theorem, Gauss’ Law, Continuation and the Equivalent Stratum: the divergence theorem and Gauss’ law, now applied to charge.
- Undergraduate electromagnetism (Griffiths level): curl, Stokes’ theorem, Faraday’s and Ampère’s laws. The Physical Sciences section covers it from the physics side.
The Hook: Listening to Lightning and the Sun
The Four Equations
| Name | Differential form | Integral form | Physical content |
|---|---|---|---|
| Gauss (electric) | \( \nabla\cdot\mathbf{D} = \rho_f \) | \( \oint\mathbf{D}\cdot d\mathbf{A} = Q_{f,\text{enc}} \) | charges are sources of \( \mathbf{D} \) |
| Gauss (magnetic) | \( \nabla\cdot\mathbf{B} = 0 \) | \( \oint\mathbf{B}\cdot d\mathbf{A} = 0 \) | no magnetic monopoles; field lines close |
| Faraday | \( \nabla\times\mathbf{E} = -\dfrac{\partial\mathbf{B}}{\partial t} \) | \( \oint\mathbf{E}\cdot d\mathbf{l} = -\dfrac{d\Phi_B}{dt} \) | changing \( \mathbf{B} \) induces a circulating \( \mathbf{E} \) |
| Ampère–Maxwell | \( \nabla\times\mathbf{H} = \mathbf{J}_f + \dfrac{\partial\mathbf{D}}{\partial t} \) | \( \oint\mathbf{H}\cdot d\mathbf{l} = I_{f,\text{enc}} + \dfrac{d\Phi_D}{dt} \) | conduction and displacement currents make \( \mathbf{H} \) circulate |
Constitutive relations
For linear, isotropic rocks:
$$\boxed{\mathbf{D} = \varepsilon\mathbf{E}, \qquad \mathbf{B} = \mu\mathbf{H}, \qquad \mathbf{J} = \sigma\mathbf{E}}$$with \( \varepsilon = \varepsilon_r\varepsilon_0 \) (\( \varepsilon_0 = 8.854\times 10^{-12} \) F/m), \( \mu = \mu_r\mu_0 \) (\( \mu_0 = 4\pi\times 10^{-7} \) H/m), and conductivity \( \sigma = 1/\rho \) (S/m; resistivity \( \rho \) in Ω m). For most rocks \( \mu_r \approx 1 \); magnetite-rich rocks are the exception.
| Property | Controls | Typical earth behaviour |
|---|---|---|
| \( \sigma \) (or \( \rho \)) | conduction current, induction, attenuation | varies over many orders of magnitude: sea water is a strong conductor (about 0.2–0.3 Ω m); clay-rich and saline-saturated rocks conduct well; dry crystalline rock is highly resistive |
| \( \varepsilon_r \) | displacement current, radar velocity | air 1; dry sand and ice a few units; water about 80 |
| \( \mu_r \) | magnetic induction | close to 1 for most rocks |
The resistivity of most rocks is controlled by their pore fluid (amount, salinity, connectivity), clay content and temperature rather than by the rock-forming minerals, which are mostly insulators.
Consequences you should be able to derive
Charge conservation. Take the divergence of Ampère–Maxwell (\( \nabla\cdot\nabla\times = 0 \)) and use Gauss:
$$\boxed{\nabla\cdot\mathbf{J} + \frac{\partial\rho_f}{\partial t} = 0}$$Charge relaxation. In a uniform conductor, \( \nabla\cdot\mathbf{J} = \sigma\nabla\cdot\mathbf{E} = (\sigma/\varepsilon)\rho_f \), so
$$\rho_f(t) = \rho_f(0)\, e^{-t/\tau}, \qquad \boxed{\tau = \frac{\varepsilon}{\sigma}}$$For a 100 Ω m rock with \( \varepsilon_r = 10 \): \( \tau = (8.854\times 10^{-11})/(0.01) = 8.9\times 10^{-9} \) s. Free charge disappears from the interior of a conductor in nanoseconds and can sit only on boundaries where \( \sigma \) changes.
Potentials. Because \( \nabla\cdot\mathbf{B} = 0 \), \( \mathbf{B} = \nabla\times\mathbf{A} \). Faraday then gives \( \nabla\times(\mathbf{E} + \partial\mathbf{A}/\partial t) = 0 \), so
$$\mathbf{E} = -\nabla\phi - \frac{\partial\mathbf{A}}{\partial t}$$a scalar-plus-vector split of the kind that the Helmholtz theorem guarantees.
Energy flux. The Poynting vector \( \mathbf{S} = \mathbf{E}\times\mathbf{H} \) (W/m²) gives the direction and rate of electromagnetic energy flow; in a conductor part of it is lost as Joule heat \( \sigma E^2 \).
Boundary Conditions
Apply the integral forms to a thin pillbox and a thin loop straddling an interface between media 1 and 2 (normal \( \hat{\mathbf{n}} \)):
| Quantity | Condition | From |
|---|---|---|
| Tangential \( \mathbf{E} \) | continuous | Faraday (loop) |
| Normal \( \mathbf{B} \) | continuous | Gauss magnetic (pillbox) |
| Tangential \( \mathbf{H} \) | continuous, unless a surface current flows | Ampère–Maxwell (loop) |
| Normal \( \mathbf{D} \) | jumps by the free surface charge | Gauss electric (pillbox) |
| Normal \( \mathbf{J} \) | continuous (steady state) | charge conservation |
The last line explains why surface charges build up at resistivity contrasts: if \( \sigma_1 E_{1n} = \sigma_2 E_{2n} \) with \( \sigma_1 \neq \sigma_2 \), then \( E_n \) must jump, and by Gauss’ law that requires a surface charge. Those charges are what make a buried conductor visible in DC resistivity and what cause static shifts in MT.
The Static Limit: DC Resistivity
With no time variation, Faraday gives \( \nabla\times\mathbf{E} = 0 \), so \( \mathbf{E} = -\nabla V \). Steady current means \( \nabla\cdot\mathbf{J} = 0 \) away from electrodes:
$$\nabla\cdot(\sigma\nabla V) = 0 \quad\xrightarrow{\ \sigma\ \text{uniform}\ }\quad \boxed{\nabla^2 V = 0}$$Laplace’s equation again, the same mathematics as gravity. For a current \( I \) injected at a point on the surface of a uniform half-space of resistivity \( \rho \), the current spreads over a hemisphere of area \( 2\pi r^2 \):
$$J = \frac{I}{2\pi r^2}, \qquad E = \rho J, \qquad \boxed{V(r) = \frac{\rho I}{2\pi r}}$$For a four-electrode array, the measured \( \Delta V/I \) is converted to an apparent resistivity with a geometric factor \( K \): \( \rho_a = K\,\Delta V/I \). For the Wenner array (equal spacings \( a \)):
$$\boxed{\rho_a = 2\pi a\,\frac{\Delta V}{I}}$$Over a uniform half-space \( \rho_a = \rho \) for every spacing; departures from that with increasing spacing reveal layering.
Time-Varying Fields: Diffusion or Waves
The governing equation
Take the curl of Faraday, use Ampère–Maxwell with \( \mathbf{J} = \sigma\mathbf{E} \), and the identity \( \nabla\times\nabla\times\mathbf{E} = \nabla(\nabla\cdot\mathbf{E}) - \nabla^2\mathbf{E} \) with \( \nabla\cdot\mathbf{E} = 0 \) in a uniform, charge-free region:
$$\boxed{\nabla^2\mathbf{E} = \mu\sigma\,\frac{\partial\mathbf{E}}{\partial t} + \mu\varepsilon\,\frac{\partial^2\mathbf{E}}{\partial t^2}}$$(\( \mathbf{H} \) obeys the same equation). The first term on the right is conduction (diffusion); the second is displacement (wave propagation). For time dependence \( e^{i\omega t} \):
$$\nabla^2\mathbf{E} = \left(i\omega\mu\sigma - \omega^2\mu\varepsilon\right)\mathbf{E}$$Which term wins
The ratio of conduction to displacement current is
$$\boxed{\frac{\lvert\mathbf{J}_{\text{cond}}\rvert}{\lvert\mathbf{J}_{\text{disp}}\rvert} = \frac{\sigma}{\omega\varepsilon}}$$| Regime | Condition | Equation | Methods |
|---|---|---|---|
| Diffusive (quasi-static) | \( \sigma \gg \omega\varepsilon \) | \( \nabla^2\mathbf{E} = \mu\sigma\,\partial_t\mathbf{E} \) | MT, AMT, CSEM, frequency- and time-domain EM, induction logging |
| Transition | \( \sigma \approx \omega\varepsilon \) | full equation | some high-frequency EM in resistive ground |
| Propagating (wave) | \( \sigma \ll \omega\varepsilon \) | \( \nabla^2\mathbf{E} = \mu\varepsilon\,\partial_t^2\mathbf{E} \) | GPR |
The crossover frequency is \( f_t = \sigma/(2\pi\varepsilon) \). For a 100 Ω m rock with \( \varepsilon_r = 10 \), \( f_t = 0.01/(2\pi\times 8.854\times 10^{-11}) \approx 1.8\times 10^{7} \) Hz, about 18 MHz. Induction methods (Hz to kHz) are far below it; GPR (tens of MHz to GHz) is above it.
Skin Depth
For a uniform plane field entering a uniform conductor in the diffusive regime, the solution is
$$E(z, t) = E_0\, e^{-z/\delta}\cos\!\left(\omega t - \frac{z}{\delta}\right), \qquad \boxed{\delta = \sqrt{\frac{2}{\omega\mu\sigma}}}$$The skin depth \( \delta \) is the depth at which the amplitude has fallen to \( 1/e \) (about 37%) and the phase has lagged by one radian. With \( \mu = \mu_0 \) and \( \omega = 2\pi f \):
$$\boxed{\delta \approx 503\sqrt{\frac{\rho}{f}}\ \text{m}} \qquad (\rho \text{ in } \Omega\,\text{m},\ f \text{ in Hz})$$| Ground | \( \rho \) (Ω m) | \( f \) | \( \delta \) |
|---|---|---|---|
| Resistive crust | 100 | 1 Hz | 5.0 km |
| Conductive sediments | 10 | 0.01 Hz (100 s) | 15.9 km |
| Sea water (taking \( \sigma = 4 \) S/m) | 0.25 | 100 Hz | 25 m |
Rules that follow at once:
- Lower frequency, deeper: \( \delta \propto f^{-1/2} \). Quartering the frequency doubles the depth. That is why MT can sound the upper mantle with long periods.
- More conductive, shallower: \( \delta \propto \rho^{1/2} \). A conductive overburden “screens” what is under it.
- Sea water is so conductive that radio-frequency communication with submerged objects is practical only at very low frequencies.
The wavelength inside the conductor is \( 2\pi\delta \), and the phase velocity \( \omega\delta \) depends on frequency: diffusion is dispersive.
Magnetotellurics
Natural source fields arrive at the surface as near-vertical plane waves (the huge contrast between air and ground refracts them to vertical). For a uniform half-space, the ratio of orthogonal horizontal fields is the impedance:
$$Z = \frac{E_x}{H_y} = \sqrt{\frac{i\omega\mu_0}{\sigma}} = \sqrt{\omega\mu_0\rho}\; e^{i\pi/4}$$So the magnitude gives resistivity and the phase is fixed:
$$\boxed{\rho_a = \frac{\lvert Z\rvert^2}{\omega\mu_0}}, \qquad \boxed{\phi = 45^\circ} \text{ for a uniform half-space}$$Over layered ground, \( \rho_a \) and \( \phi \) vary with period: a phase above 45° means resistivity decreasing with depth at the depth being sampled; below 45° means it is increasing.
Field-unit form. With \( E \) in mV/km and \( B = \mu_0 H \) in nT, and period \( T \) in seconds:
$$\boxed{\rho_a = 0.2\, T \left\lvert\frac{E}{B}\right\rvert^2}$$(Derivation: \( \rho_a = \mu_0\lvert E/B\rvert^2/\omega = \frac{\mu_0}{2\pi}T\lvert E/B\rvert^2 \); \( \mu_0/2\pi = 2\times 10^{-7} \), and \( (1\ \text{mV/km})/(1\ \text{nT}) = 10^{3} \) m/s, whose square gives \( 10^{6} \); the product is 0.2.)
The Wave Regime: Ground-Penetrating Radar
When \( \sigma \ll \omega\varepsilon \), the field propagates with speed
$$\boxed{v = \frac{1}{\sqrt{\mu\varepsilon}} = \frac{c}{\sqrt{\varepsilon_r}}} \qquad (\mu_r = 1,\ c = 0.3\ \text{m/ns})$$| Medium | \( \varepsilon_r \) (typical) | \( v \) (m/ns) |
|---|---|---|
| Air | 1 | 0.30 |
| Dry sand / ice | about 3–5 | about 0.13–0.17 |
| Moist soil (example) | 9 | 0.10 |
| Fresh water | about 80 | about 0.033 |
Reflections come from contrasts in \( \varepsilon_r \) (mainly water content). Depth from two-way time \( t \) is \( d = vt/2 \). The low-loss attenuation constant is approximately
$$\alpha \approx \frac{\sigma}{2}\sqrt{\frac{\mu}{\varepsilon}} = \frac{\sigma}{2}\,\frac{376.7\ \Omega}{\sqrt{\varepsilon_r}}\ \ \text{(Np/m)}$$so conductive (clay-rich or saline) ground kills radar penetration, while dry sand, ice and resistive rock let it go deep.
Memory Tricks
Don’t Confuse
| This | vs | That |
|---|---|---|
| Conduction current \( \sigma\mathbf{E} \): dominates EM induction | displacement current \( \varepsilon\,\partial_t\mathbf{E} \): dominates GPR | |
| Diffusion: \( \nabla^2 E = \mu\sigma\,\partial_t E \), first time derivative | wave: \( \nabla^2 E = \mu\varepsilon\,\partial_t^2 E \), second derivative | |
| Skin depth \( \delta \): 1/e amplitude depth | wavelength in the conductor \( 2\pi\delta \) | |
| Apparent resistivity: property of the measurement | true resistivity: property of a layer | |
| \( \nabla\cdot\mathbf{B} = 0 \): no monopoles | \( \nabla\times\mathbf{E} = -\partial_t\mathbf{B} \): induction | |
| Charge relaxation time \( \varepsilon/\sigma \) (nanoseconds in rock) | EM diffusion time over a depth \( L \): about \( \mu\sigma L^2 \) |
Common Mistakes
Practice
All questions below are original practice questions written for this page. They are not from any CSIR NET paper. Use \( \mu_0 = 4\pi\times 10^{-7} \) H/m, \( \varepsilon_0 = 8.854\times 10^{-12} \) F/m, \( c = 0.3 \) m/ns.
Level 1: Foundation
- Which Maxwell equation expresses the absence of magnetic monopoles?
- Write the skin-depth formula in practical units.
- What is the MT impedance phase over a uniform half-space?
Answers
- \( \nabla\cdot\mathbf{B} = 0 \).
- \( \delta \approx 503\sqrt{\rho/f} \) m.
- 45°.
Level 2: Part B Style
Practice Q1. The skin depth for a 1 Hz field in ground of resistivity 100 Ω m is about:
(a) 50 m (b) 503 m (c) 5.0 km (d) 50 km
Answer: (c) 5.0 km
\( 503\sqrt{100/1} = 503\times 10 = 5030 \) m.
Practice Q2. A GPR reflection arrives at a two-way time of 80 ns in soil with \( \varepsilon_r = 9 \). The reflector depth is:
(a) 2 m (b) 4 m (c) 8 m (d) 12 m
Answer: (b) 4 m
\( v = 0.3/\sqrt{9} = 0.1 \) m/ns. \( d = vt/2 = 0.1\times 80/2 = 4 \) m. (c) forgets to halve the two-way time; (d) uses \( c \) with no correction.
Practice Q3. Across a boundary between two rocks of different conductivity, with no surface current, which quantity is necessarily continuous?
(a) normal component of \( \mathbf{E} \) (b) tangential component of \( \mathbf{E} \) (c) normal component of \( \mathbf{D} \) (d) tangential component of \( \mathbf{J} \)
Answer: (b)
Tangential \( \mathbf{E} \) is continuous from Faraday’s law. Normal \( \mathbf{E} \) and normal \( \mathbf{D} \) jump because surface charge accumulates; tangential \( \mathbf{J} = \sigma E_t \) jumps because \( \sigma \) does.
Practice Q4. For a current \( I \) injected at a point on the surface of a uniform half-space of resistivity \( \rho \), the potential at distance \( r \) is:
(a) \( \rho I/(4\pi r) \) (b) \( \rho I/(2\pi r) \) (c) \( \rho I/(2\pi r^2) \) (d) \( \rho I r/(2\pi) \)
Answer: (b)
The current spreads through a hemisphere of area \( 2\pi r^2 \): \( J = I/(2\pi r^2) \), \( E = \rho J \), and integrating \( E \) from \( r \) to infinity gives \( \rho I/(2\pi r) \). (a) is the full-space result.
Level 3: Part C Style
Practice Q5. An MT station records, at a period of 10 s, \( E_x = 5 \) mV/km and \( B_y = 2 \) nT, with an impedance phase of 45°. Which statements are correct?
- The apparent resistivity is 12.5 Ω m.
- The skin depth at this period is about 5.6 km.
- At a period of 1000 s, in the same uniform ground, the skin depth would be about 56 km.
- A phase of 60° at longer periods would indicate a resistive layer at depth.
(a) 1 and 2 only (b) 1, 2 and 3 only (c) 1, 3 and 4 only (d) 1, 2, 3 and 4
Answer: (b) 1, 2 and 3 only
- \( 0.2\times 10\times 2.5^2 = 12.5 \) Ω m. Correct.
- \( 503\sqrt{12.5/0.1} = 503\times 11.18 = 5624 \) m. Correct.
- Period ×100, frequency ÷100, \( \delta \) ×10: about 56 km. Correct.
- A phase above 45° indicates resistivity decreasing with depth, that is, a conductor. Wrong.
Practice Q6. Consider a rock of resistivity 100 Ω m and \( \varepsilon_r = 10 \). Which statements are correct?
- At 1 kHz, conduction current exceeds displacement current by a factor of about \( 1.8\times 10^{4} \).
- At 100 MHz, displacement current exceeds conduction current.
- The frequency at which the two currents are equal is about 18 MHz.
- At 1 kHz the field in this rock travels at about \( c/\sqrt{10} \).
(a) 1 and 3 only (b) 1, 2 and 3 only (c) 2 and 4 only (d) 1, 2, 3 and 4
Answer: (b) 1, 2 and 3 only
\( \sigma = 0.01 \) S/m; \( \varepsilon = 8.854\times 10^{-11} \) F/m.
- \( \omega\varepsilon = 2\pi(10^3)(8.854\times10^{-11}) = 5.56\times 10^{-7} \); ratio \( 0.01/5.56\times10^{-7} = 1.8\times 10^{4} \). Correct.
- At \( 10^8 \) Hz, \( \omega\varepsilon = 5.56\times 10^{-2} \); ratio \( 0.18 \): displacement dominates. Correct.
- \( f_t = \sigma/(2\pi\varepsilon) = 0.01/5.56\times 10^{-10} = 1.8\times 10^{7} \) Hz. Correct.
- At 1 kHz the regime is diffusive; there is no wave velocity \( c/\sqrt{\varepsilon_r} \). Wrong.
Practice Q7. In a Wenner survey with \( a = 20 \) m, a current of 0.5 A gives a potential difference of 0.80 V between the inner electrodes. On doubling \( a \) to 40 m, the same current gives 0.40 V. Which conclusion is best supported?
(a) apparent resistivity about 201 Ω m at both spacings: consistent with uniform ground to the depth sampled (b) apparent resistivity rises from 201 to 402 Ω m: a resistive layer at depth (c) apparent resistivity falls from 201 to 100 Ω m: a conductive layer at depth (d) the data are inconsistent with Laplace’s equation
Answer: (a)
\( \rho_a = 2\pi a\,\Delta V/I \).
\( a = 20 \): \( 2\pi(20)(0.80/0.5) = 2\pi(20)(1.6) = 201 \) Ω m.
\( a = 40 \): \( 2\pi(40)(0.40/0.5) = 2\pi(40)(0.8) = 201 \) Ω m.
Equal apparent resistivities at both spacings are what a uniform half-space gives. Options (b) and (c) forget that the geometric factor doubles with \( a \): halving \( \Delta V \) at double spacing is exactly the uniform-ground behaviour of \( V \propto 1/r \).
Quick Revision Table
| Idea | Formula or fact |
|---|---|
| Maxwell | \( \nabla\cdot\mathbf{D} = \rho_f \), \( \nabla\cdot\mathbf{B} = 0 \), \( \nabla\times\mathbf{E} = -\partial_t\mathbf{B} \), \( \nabla\times\mathbf{H} = \mathbf{J} + \partial_t\mathbf{D} \) |
| Constitutive | \( \mathbf{D} = \varepsilon\mathbf{E} \), \( \mathbf{B} = \mu\mathbf{H} \), \( \mathbf{J} = \sigma\mathbf{E} \) |
| Continuity / relaxation | \( \nabla\cdot\mathbf{J} + \partial_t\rho = 0 \); \( \tau = \varepsilon/\sigma \) |
| Boundary | tangential \( E \), normal \( B \) continuous; normal \( J \) continuous (DC) |
| DC limit | \( \nabla^2 V = 0 \); half-space \( V = \rho I/(2\pi r) \); Wenner \( \rho_a = 2\pi a\,\Delta V/I \) |
| Telegraph equation | \( \nabla^2\mathbf{E} = \mu\sigma\partial_t\mathbf{E} + \mu\varepsilon\partial_t^2\mathbf{E} \) |
| Regime | \( \sigma/\omega\varepsilon \gg 1 \) diffusion; \( \ll 1 \) waves; \( f_t = \sigma/2\pi\varepsilon \) |
| Skin depth | \( \sqrt{2/\omega\mu\sigma} \approx 503\sqrt{\rho/f} \) m |
| MT | \( \rho_a = \lvert Z\rvert^2/\omega\mu_0 = 0.2T\lvert E/B\rvert^2 \); uniform phase 45° |
| GPR | \( v = c/\sqrt{\varepsilon_r} \); \( d = vt/2 \) |
Key Takeaways
What’s Next
- Helmholtz Theorem and Seismic Wave Propagation: splitting a vector field into curl-free and divergence-free parts, and the P and S waves that result.
- Field Theory: Quick Revision.
- Back to the Field Theory overview.
- For the solid-Earth context of conductivity, heat flow and the geomagnetic field, see Gravity, Geomagnetism, Heat Flow and Isostasy.