Skip to content

Bright Spots, AVO, VSP, 3D Seismics and Seismic Stratigraphy

Direct hydrocarbon indicators, AVO intercept-gradient and classes, vertical seismic profiling, 3D survey design and seismic stratigraphy for CSIR NET.

  • 21 min read
  • Updated
On this page · 15 sections
  1. Prerequisites
  2. The Hook: When Amplitude Became a Drilling Tool
  3. Rock Physics Behind Amplitude
  4. Bright Spots and Other Direct Hydrocarbon Indicators
  5. AVO: Amplitude Versus Offset (Angle)
  6. Vertical Seismic Profiling (VSP)
  7. 3D Seismics
  8. Seismic Stratigraphy
  9. Memory Tricks
  10. Don’t Confuse
  11. Common Mistakes
  12. Practice
  13. Quick Revision Table
  14. Key Takeaways
  15. What’s Next

Prerequisites

The Hook: When Amplitude Became a Drilling Tool

How CSIR NET asks it. Part C (Geophysics) asks which feature is a direct hydrocarbon indicator and why, AVO class from intercept and gradient, Poisson’s ratio from \(V_P/V_S\), VSP wavefields and time-depth numbers, 3D bin-size and fold logic, and seismic-stratigraphic terms (onlap, downlap, toplap, truncation; seismic facies; systems tracts) applied to a described section.


Rock Physics Behind Amplitude

Replacing brine by gas in the pores of a porous sandstone:

PropertyEffect of gasWhy
\(V_P\)Falls sharply, even at low gas saturationGas makes the pore fluid very compressible, lowering the bulk modulus of the saturated rock (Gassmann fluid substitution)
\(V_S\)Slightly risesShear modulus is unaffected by fluid; density falls
\(\rho\)FallsGas is far lighter than brine
\(V_P/V_S\), Poisson’s ratio \(\sigma\)FallBecause \(V_P\) drops while \(V_S\) does not
ImpedanceFallsBoth \(V_P\) and \(\rho\) drop

Poisson’s ratio from velocities:

$$\sigma = \frac{(V_P/V_S)^2 - 2}{2\left[(V_P/V_S)^2 - 1\right]}$$

\(V_P/V_S = 2\) gives \(\sigma = 1/3\) (typical of brine-saturated sands and shales); \(V_P/V_S = 1.5\) gives \(\sigma = 0.10\) (typical of gas sands).


Bright Spots and Other Direct Hydrocarbon Indicators

DHIWhat causes itHow it looksPitfalls
Bright spotLow-impedance gas sand below higher-impedance shaleAnomalously strong negative reflection at the top of the reservoir, often limited to the structural crestCoals, low-impedance volcanic ash, tuning of thin beds, fizz gas
Dim spotHigh-impedance reservoir (e.g. consolidated sand, carbonate) whose impedance gas reduces towards that of the cap rockLocally weaker reflection over the crestEasy to miss; lithology changes do the same
Polarity reversalGas lowers a slightly-higher-impedance sand to below the shaleReflection changes sign where it crosses the gas–water contact laterallyNeeds careful phase control
Flat spotFluid contact (gas–water, gas–oil, oil–water): impedance increases from gas- to water-filled sandFlat (or nearly flat after depth conversion) positive reflection cutting across dipping strataFlat lithological layers, multiples, other flat-lying interfaces that mimic a contact
Velocity push-down (sag)Slow gas column above deeper reflectorsUnderlying reflectors sag in time beneath the accumulationLateral velocity changes in the overburden
Frequency loss / low-frequency shadowAbsorption in gasLower dominant frequency beneath the reservoirProcessing artefacts
Gas chimneyGas leaking upwardsVertical zone of disturbed, low-amplitude reflectionsFaults, processing noise
Amplitude conformanceThe anomaly is limited by a fluid contactAmplitude edge follows a structural contourStratigraphic pinch-outs can coincide

Polarity display depends on the convention used, so always check how a known positive reflection (such as a hard sea floor) appears on the section before calling a bright spot “negative”.

Push-down example. A 50 m gas column with \(V_P = 2000\) m/s, replacing brine sand with \(V_P = 2500\) m/s, delays deeper reflections by

$$\Delta t = 2h\left(\frac{1}{V_{gas}} - \frac{1}{V_{brine}}\right) = 100\left(\frac{1}{2000} - \frac{1}{2500}\right) = 0.010\ \mathrm{s} = 10\ \mathrm{ms}$$

AVO: Amplitude Versus Offset (Angle)

Basis

From the Zoeppritz equations, linearised by Aki and Richards and rearranged by Shuey (derived on the first page of this unit):

$$R(\theta) \approx A + B\sin^2\theta$$
  • Intercept \(A\): the normal-incidence reflection coefficient, controlled by impedance contrast.
  • Gradient \(B\): the rate of change with \(\sin^2\theta\), strongly affected by the contrast in Poisson’s ratio. A drop in Poisson’s ratio downward (shale over gas sand) makes \(B\) more negative.
  • Ostrander’s work on gas sands showed that a large Poisson’s-ratio contrast makes reflection amplitude change markedly with offset, which turned AVO into a fluid indicator.

Workflow

graph TD
    A["Amplitude-preserved
pre-stack CMP gathers"] --> B["NMO, mute,
offset-to-angle conversion"] B --> C["Fit R = A + B sin²θ
at each time sample"] C --> D["Intercept and
gradient volumes"] D --> E["Crossplot A vs B:
background trend"] E --> F["Anomalies off-trend:
candidate hydrocarbons"] F --> G["Calibrate with wells,
fluid substitution, models"]

Requirements: amplitude-preserving processing (no AGC), correct spherical-divergence and absorption compensation, NMO stretch control, conversion from offset to angle with a velocity model, and awareness of tuning, anisotropy and noise at far offsets.

AVO classes (top of a gas sand under shale)

ClassGas-sand impedance vs shaleIntercept \(A\)Gradient \(B\)Amplitude behaviour with angle
IHigherLarge positiveNegativePositive reflection dims with angle; may reverse polarity at far offsets
II (IIp if polarity reverses)Nearly equalSmall (positive or negative)NegativeWeak near offsets, grows at far offsets; polarity reversal if \(A > 0\)
IIILowerNegativeNegativeStrong negative at all offsets and brighter with angle: the classic bright spot
IVLowerNegativePositiveStrong negative near offsets whose magnitude decreases with angle (e.g. when the overlying rock is hard and fast)

Classes I to III follow Rutherford and Williams; class IV was added later by Castagna and co-workers.

Intercept–gradient crossplot

  • Brine sands and shales fall along a background trend with negative slope through the origin.
  • Gas sands plot away from it: tops of class III sands in the quadrant with \(A < 0\), \(B < 0\) (positive product \(A\times B\)); bases in the opposite quadrant.
  • Common derived attributes: the product \(A\times B\) (high for class III), \(A + B\) (a pseudo-Poisson’s-ratio reflectivity), near and far angle stacks, and “fluid factor” type deviations from the background trend.

Vertical Seismic Profiling (VSP)

In a VSP, the source is at the surface and receivers (clamped multi-component geophones or hydrophones) are placed at many depths in a borehole. Because the receiver is inside the earth, it records both the downgoing and the upgoing wavefields.

Types

TypeGeometryMain use
Check-shot surveyFew, widely spaced levels; first breaks onlyTime–depth curve, sonic-log calibration
Zero-offset VSPSource near the wellheadTime–depth, interval velocities, well-to-seismic tie, multiple identification, corridor stack
Offset VSPSource at a fixed offsetImaging a strip of the reflector away from the well, AVO calibration, converted waves
Walkaway VSPMany source positions along a lineAngle-dependent amplitudes, anisotropy, 2D image around the well
Walk-above VSPSource moved to stay above receivers in a deviated wellVertical-incidence data along a deviated well
Reverse VSPSource in the well (or drill bit), receivers at the surfaceImaging with many surface receivers; drill-bit seismic
3D VSPAreal grid of sourcesImaging around the well in 3D

Wavefields on a zero-offset VSP

On a display of depth (vertical) against one-way recording time (horizontal):

  • The first break (direct downgoing P) arrives later with increasing depth; its slope gives interval velocity: \(V_{int} = \Delta z/\Delta t_{fb}\).
  • Downgoing multiples are parallel to the first break.
  • Upgoing reflections arrive earlier at deeper receivers (the receiver is closer to the reflector), so they slope the opposite way, and each meets the first-break curve at the depth of its reflector.
  • Tube waves, slow waves travelling in the borehole fluid, are a major noise, as are casing-ringing and converted waves.

Key relation. For an upgoing primary recorded at depth \(z\) at time \(t_{up}(z)\), with first-break time \(t_{fb}(z)\):

$$t_{up}(z) + t_{fb}(z) = T_{surface}$$

where \(T_{surface}\) is the two-way time of that reflection on surface seismic. Adding the first-break time to each trace aligns upgoing events at their surface two-way times (flattening them); subtracting it aligns the downgoing waves.

Processing and uses

  1. Pick first breaks → time–depth curve and interval velocities.
  2. Separate downgoing and upgoing wavefields (median filtering after alignment, or f-k filtering; they dip in opposite directions).
  3. Deconvolve the upgoing field with the downgoing field: the downgoing wavefield is the actual source wavelet plus all downgoing multiples, so this deconvolution removes both.
  4. Flatten upgoing events to two-way time and make a corridor stack (summing a narrow window just after the first break, where multiples generated deeper have not yet arrived).
  5. Compare with surface seismic and synthetic seismograms.

Uses: precise well ties (which reflection is which horizon), checking whether an event is a primary or a multiple, Q estimation from the change of the direct wavelet with depth, looking ahead of the bit, imaging near salt flanks and steep dips, and calibrating anisotropy and AVO.


3D Seismics

Why 3D

A 2D line assumes all reflections come from the vertical plane below it. In real structures energy arrives from the side (sideswipe), 2D migration cannot put it back, and maps interpolated between lines miss small faults and channels. A 3D survey samples the subsurface on a dense areal grid and is migrated in 3D, so reflectors move to their true positions in both directions and the Fresnel zone shrinks in both horizontal directions.

Vocabulary

TermMeaning
InlineDirection of receiver lines (land) or sail lines (marine)
CrosslinePerpendicular to inline
BinSmall rectangular cell (for example 12.5 m × 25 m or 25 m × 25 m) collecting all traces whose midpoints fall in it
Fold per binNumber of traces in a bin; total fold = inline fold × crossline fold
Offset and azimuth distributionRange of offsets and source–receiver directions in each bin; uniformity matters for AVO and multiple attenuation
Patch / templateThe set of live receivers for one shot
Migration aperture / haloExtra survey area so that dipping events at the edge of the target can be migrated in

For orthogonal land geometry the bin dimensions are half the receiver interval (inline) and half the source interval (crossline).

Geometries

  • Land: orthogonal (source lines perpendicular to receiver lines, the most common), brick, slant and zigzag layouts.
  • Marine: a vessel towing several streamers and one or more source arrays gives narrow-azimuth data; multi-vessel wide-azimuth and multi-azimuth surveys and ocean-bottom nodes give the full azimuth coverage needed below salt.

Bin size and spatial aliasing

For a reflector dip \(\theta\), interval velocity \(V\) and highest frequency to be imaged \(f_{max}\), unaliased sampling of the zero-offset time dip \(2\sin\theta/V\) requires

$$\boxed{\Delta x \le \frac{V}{4f_{max}\sin\theta}}$$

Example: \(V = 3000\) m/s, \(f_{max} = 60\) Hz, \(\theta = 30°\): \(\Delta x \le 3000/(4\times60\times0.5) = 25\) m.

Interpreting 3D volumes

  • Time slices: horizontal sections at constant time; dipping reflectors appear as bands whose width shows dip; faults show as offsets of the bands.
  • Horizon slices: amplitude extracted along (or parallel to) an interpreted horizon; show channels, fans, reefs as map-view depositional shapes.
  • Attributes: amplitude (DHIs), coherence/variance (faults and channel edges), curvature (fractures, flexures), spectral decomposition (tuning thickness variations), impedance from inversion.
  • Geobodies and visualisation: opacity rendering of anomalies in 3D.

4D (time-lapse) and multi-component

  • 4D seismic repeats a 3D survey over a producing field. Differences in amplitude and travel time show where fluids have moved, pressure has changed and where bypassed oil remains. Repeatability of source and receiver positions is the key requirement; permanent ocean-bottom arrays are used in some fields.
  • Multi-component (4C/9C) surveys record converted PS waves, which image through gas clouds (S waves are little affected by gas) and give \(V_P/V_S\).

Seismic Stratigraphy

The founding principle

Primary seismic reflections are generated by physical surfaces with impedance contrasts: bedding surfaces and unconformities. These surfaces are essentially time lines (chronostratigraphic surfaces). A reflection therefore follows a time surface and may cross diachronous lithological (facies) boundaries. This makes seismic data a tool for stratigraphy and depositional history, not just structure. The approach was set out by Vail and co-workers at Exxon in AAPG Memoir 26 (1977).

Seismic stratigraphy proceeds in three steps:

  1. Seismic sequence analysis: pick sequence boundaries (unconformities and their correlative conformities) from reflection terminations.
  2. Seismic facies analysis: describe and interpret reflection character within each sequence.
  3. Relative sea-level analysis: reconstruct coastal onlap and relative sea-level change.

Reflection terminations

TerminationPositionGeometryTypical meaning
OnlapAt the base of a unitInitially horizontal strata end against an inclined surface, landwardProgressive infilling, transgression, rising relative sea level
DownlapAt the baseInitially inclined strata end down-dip against a flatter surfaceProgradation (clinoforms) over a surface of condensed deposition
ToplapAt the topInclined strata thin and end up-dip against an overlying surface, without erosionSediment bypass at base level; progradation with little accommodation
Erosional truncationAt the topStrata cut by an erosional surfaceErosion; unconformity (sequence boundary)
ConcordanceTop or baseStrata parallel to the boundaryNo break evident

Baselap = onlap + downlap (both at the base). Onlap and downlap can be hard to distinguish after later tilting.

Seismic facies

Parameters: reflection configuration, continuity, amplitude, frequency, interval velocity and the external form of the unit.

Internal configurationInterpretation
Parallel / subparallelUniform deposition on a stable or uniformly subsiding surface (shelf, basin plain)
DivergentWedge thickening down-dip: differential subsidence or tilting during deposition
Sigmoid clinoformsPrograding slope with preserved topsets: low energy, high supply, rising relative sea level (aggradation)
Oblique clinoformsPrograding slope with toplap, no topsets: high energy, little accommodation, sediment bypass
Complex sigmoid–oblique, shingled, hummockyMixed or variable conditions; shingled = thin prograding units in shallow water
ChaoticSlumps, slides, channel fills, high energy or deformation
Reflection-freeHomogeneous bodies: massive sands or shales, salt, igneous intrusions, reef cores

External forms: sheet, sheet drape, wedge, bank, lens, mound (reefs, fans, contourite drifts, volcanic piles) and fill (channel, trough, canyon, basin fills).

Sequence stratigraphy in one diagram

graph TD
    SB["Sequence boundary
unconformity + correlative conformity
erosional truncation below, onlap above"] --> LST["Lowstand systems tract
basin-floor fans, slope fans,
prograding wedge"] LST --> TS["Transgressive surface"] TS --> TST["Transgressive systems tract
retrogradational, onlap landward"] TST --> MFS["Maximum flooding surface
condensed section,
downlap surface"] MFS --> HST["Highstand systems tract
aggradational then progradational,
downlap onto MFS"] HST --> SB2["Next sequence boundary"]
  • A depositional sequence is a relatively conformable succession of genetically related strata bounded by unconformities or their correlative conformities.
  • The maximum flooding surface (MFS) is the surface onto which highstand clinoforms downlap; it is often a condensed, organic-rich (source-rock) interval.
  • Systems tracts link reflection geometry to the relative sea-level cycle: falling stage and lowstand (forced regression, fans), transgression (retrogradation), highstand (aggradation then progradation).

Memory Tricks

Don’t Confuse

ThisvsThat
Bright spot: anomalously strong reflection at top of a low-impedance gas sandvsFlat spot: flat reflection at a fluid contact, cutting across dip
Dim spot: gas reduces an originally strong (hard-sand) contrastvsBright spot: gas increases an originally weak or negative contrast
AVO intercept \(A\): normal incidence, impedancevsAVO gradient \(B\): change with angle, Poisson’s-ratio contrast
Class III: \(A < 0\), \(B < 0\), brightensvsClass IV: \(A < 0\), \(B > 0\), fades
Check-shot: first breaks onlyvsVSP: full waveforms, up- and downgoing fields
Zero-offset VSP: 1D time-depth, tievsWalkaway VSP: many offsets, AVO and anisotropy
Time slice: constant time, cuts across horizonsvsHorizon slice: follows a horizon, shows depositional shapes
3D: one surveyvs4D: repeated 3D surveys over time
Onlap: horizontal strata end against an inclined surfacevsDownlap: inclined strata end down-dip on a flatter surface
Toplap: non-erosional, bypassvsTruncation: erosional
Sigmoid clinoforms: topsets preserved, rising sea levelvsOblique clinoforms: toplap, no topsets, little accommodation

Common Mistakes


Practice

All questions below are original practice questions written in CSIR NET Part C (Geophysics) style. They are not previous-year questions.

Level 1: Foundation

  1. What fluid feature does a flat spot usually mark?
  2. On a zero-offset VSP, which wavefield arrives earlier at deeper receivers?
  3. What is downlap?
Answers
  1. A fluid contact (gas–water, gas–oil or oil–water).
  2. The upgoing (reflected) wavefield.
  3. Initially inclined strata terminating down-dip against an underlying flatter surface (a baselap termination, typical of prograding clinoforms).

Level 2: Part B Style

Q1 (practice). At the top of a sand, AVO analysis gives intercept \(A = -0.12\) and gradient \(B = -0.20\). The response is best described as:

  • (a) Class I, dimming with offset
  • (b) Class II with polarity reversal
  • (c) Class III, brightening with offset
  • (d) Class IV, fading with offset
Answer and explanation

(c). A clearly negative intercept (low-impedance sand) with a negative gradient: the reflection becomes more negative with angle. Class IV would need \(B > 0\); class I needs a large positive \(A\).

Q2 (practice). In a zero-offset VSP, first breaks arrive at 0.500 s at 1000 m and 0.580 s at 1200 m. At 1000 m an upgoing reflection arrives at 0.900 s. The interval velocity between 1000 and 1200 m, and the surface two-way time of that reflection, are:

  • (a) 2500 m/s and 1.40 s
  • (b) 2000 m/s and 1.40 s
  • (c) 2500 m/s and 0.40 s
  • (d) 1250 m/s and 1.80 s
Answer and explanation

(a). \(V_{int} = 200/0.080 = 2500\) m/s. \(T_{surface} = t_{up} + t_{fb} = 0.900 + 0.500 = 1.40\) s. Option (c) subtracts instead of adding. The reflector lies at the depth where the upgoing event meets the first-break curve, i.e. where the one-way time is 0.70 s.

Q3 (practice). A 3D survey must image dips up to 30° at frequencies up to 60 Hz where the velocity is 3000 m/s. The largest bin dimension that avoids spatial aliasing is:

  • (a) 12.5 m
  • (b) 25 m
  • (c) 50 m
  • (d) 100 m
Answer and explanation

(b). \(\Delta x \le V/(4f_{max}\sin\theta) = 3000/(4\times60\times0.5) = 25\) m. A 12.5 m bin also satisfies the condition but is not the largest; 50 m would alias the 60 Hz dipping energy.

Q4 (practice). In a transgressive–regressive succession, the surface onto which overlying highstand clinoforms downlap is most likely:

  • (a) a sequence boundary
  • (b) the transgressive surface
  • (c) the maximum flooding surface
  • (d) an erosional truncation surface
Answer and explanation

(c). The maximum flooding surface caps the transgressive systems tract and is the downlap surface for highstand progradation. Sequence boundaries show truncation below and onlap above.

Level 3: Part C Style

Q1 (practice). A sandstone reservoir has these properties:

State\(V_P\) (m/s)\(V_S\) (m/s)\(\rho\) (g/cm³)
Brine-filled250012502.20
Gas-filled200013302.05

A 50 m gas column sits on top of the brine leg.

(i) Compute Poisson’s ratio in each state. (ii) Compute the normal-incidence reflection coefficient at the gas–water contact and state what feature it forms. (iii) Compute the time push-down of reflectors beneath the gas column.

Answer and worked solution
  1. Brine: \(V_P/V_S = 2.00\) → \(\sigma = (4 - 2)/(2\times3) = 0.333\). Gas: \(V_P/V_S = 1.504\), squared 2.261 → \(\sigma = 0.261/(2\times1.261) = 0.104\). A large fall in Poisson’s ratio: the AVO signature of gas.
  2. \(Z_{gas} = 2.0\times2.05 = 4.10\); \(Z_{brine} = 2.5\times2.20 = 5.50\) (units of \(10^6\) kg m⁻² s⁻¹). \(R = (5.50 - 4.10)/(5.50 + 4.10) = 1.40/9.60 = +0.146\). A positive, horizontal (in depth) reflection at the contact: a flat spot.
  3. \(\Delta t = 2(50)(1/2000 - 1/2500) = 100\times0.0001 = 0.010\) s = 10 ms of push-down.

Q2 (practice). At the top of a reservoir, amplitude-preserved angle stacks give \(R = -0.10\) at 10° and \(R = -0.16\) at 30°. Using \(R = A + B\sin^2\theta\), consider:

(A) \(A \approx -0.09\) and \(B \approx -0.27\). (B) The response is Class III. (C) The product \(A\times B\) is positive, as expected for the top of a class III gas sand. (D) The analysis would be unaffected if a 500 ms AGC had been applied to the gathers first.

Which are correct?

  • (a) A, B and C only
  • (b) A and D only
  • (c) B, C and D only
  • (d) A, B, C and D
Answer and worked solution

(a) A, B and C.

  • \(\sin^2 10° = 0.0302\), \(\sin^2 30° = 0.25\). \(B = (-0.16 + 0.10)/(0.25 - 0.0302) = -0.06/0.2198 = -0.273\). \(A = -0.10 - B(0.0302) = -0.10 + 0.0082 = -0.092\). (A) correct.
  • (B) Negative intercept, negative gradient, brightening: class III. Correct.
  • (C) \((-0.092)(-0.273) = +0.025 > 0\). Correct.
  • (D) Wrong: AGC rescales windows trace by trace and distorts the offset-dependent amplitudes AVO measures.
  • Extrapolating, \(R(40°) \approx -0.092 - 0.273\times0.413 = -0.205\), though far-angle estimates should be checked against the full Zoeppritz response.

Q3 (practice). A migrated 2D section across a passive margin shows, from bottom to top:

  • Unit 1: parallel reflections, cut at the top by a surface S1.
  • Above S1, near the basin floor: a mounded unit whose reflections onlap S1 on both sides.
  • Unit 3: reflections that step progressively landward and onlap S1 landward, capped by a surface S2.
  • Unit 4: sigmoid clinoforms whose bottomsets downlap onto S2.

Which interpretation is consistent?

  • (a) S1 is a sequence boundary, the mound is a lowstand basin-floor fan, unit 3 is a transgressive systems tract, S2 is a maximum flooding surface and unit 4 is a highstand systems tract.
  • (b) S1 is a maximum flooding surface, the mound is a reef in the highstand, S2 is a sequence boundary.
  • (c) S1 is a correlative conformity with no erosion, unit 3 is a lowstand prograding wedge, S2 is a transgressive surface.
  • (d) All four units belong to one highstand systems tract.
Answer and worked solution

(a).

  • Truncation of unit 1 at S1 with onlap above it marks an unconformity: a sequence boundary.
  • A mounded body on the basin floor, onlapping the boundary, is the classic lowstand basin-floor fan.
  • Landward-stepping (retrogradational) reflections with landward onlap are the transgressive systems tract.
  • The surface on which the next clinoforms downlap is the maximum flooding surface; sigmoid clinoforms above it, with topsets, are the highstand systems tract.
  • (b) and (c) invert the meaning of truncation and downlap; (d) ignores the bounding surfaces.

Quick Revision Table

ItemFact
Gas effect\(V_P\) falls sharply; \(V_S\) slightly up; \(\rho\) down; \(\sigma\) down
Poisson’s ratio\(V_P/V_S = 2\) → 1/3; 1.5 → 0.10
Bright spotStrong negative top of low-impedance gas sand; look-alikes: coal, fizz gas, tuning
Dim spot / flat spotWeaker crest reflection over hard reservoir / flat positive reflection at fluid contact
Push-down\(\Delta t = 2h(1/V_{gas} - 1/V_{brine})\)
AVO\(R \approx A + B\sin^2\theta\); \(A\) impedance, \(B\) Poisson contrast
ClassesI (+A, dims), II (≈0 A, grows), III (−A, −B, brightens), IV (−A, +B, fades)
VSP wavefieldsFirst break and downgoing slope one way; upgoing the other way
VSP relation\(t_{up} + t_{fb} = T_{surface}\)
VSP usesTime–depth, well tie, multiples, Q, look-ahead, corridor stack
3D binHalf receiver × half source interval; \(\Delta x \le V/(4f_{max}\sin\theta)\)
3D interpretationTime slices, horizon slices, coherence, curvature, spectral decomposition
4DRepeat 3D; fluid and pressure changes; repeatability
Seismic stratigraphyReflections follow time surfaces (Vail and co-workers, AAPG Memoir 26)
TerminationsOnlap, downlap (baselap); toplap, truncation (top)
FaciesParallel, divergent, sigmoid, oblique, chaotic, reflection-free; mound, fill
Systems tractsSB → LST → TS → TST → MFS (downlap surface) → HST

Key Takeaways

What’s Next

Advertisement
Advertisement