Snell's Law, Ray Theory and the Zoeppritz Equations
Seismic wave speeds, Snell's law, ray parameter, ray theory, Fresnel zone, reflection coefficients, mode conversion and Zoeppritz equations for CSIR NET.
- 19 min
On this page · 13 sections
Prerequisites
- Seismic Methods: chapter overview — where this page sits in the unit.
- Earth Sciences — the Part B units on the Earth’s interior give the elastic-wave basics (P, S and surface waves) that this page sharpens.
- Helmholtz Theorem and Seismic Wave Propagation — how the elastic wave equation splits into P and S potentials.
- Elasticity and waves at MSc level: Hooke’s law, the wave equation, plane-wave solutions. The Physical Sciences section treats waves and boundary conditions in general.
- Quick trigonometry and logarithms, practised in Numerical Ability.
The Hook: A Shot, a Spread and Three Straight Lines
How CSIR NET asks it. In the Geophysics section of Part C: refraction angle and critical angle from Snell’s law, ray parameter, reflection and transmission coefficients from impedances, energy partition, which converted waves exist at a boundary, Fresnel-zone and tuning numbers, and the logic of the Zoeppritz equations and their linear approximations (the basis of AVO, covered in Bright Spots, AVO, VSP, 3D and Seismic Stratigraphy).
Elastic Waves and Seismic Velocities
In an isotropic, homogeneous, linearly elastic solid with bulk modulus \(K\), shear modulus \(\mu\) and density \(\rho\):
$$V_P = \sqrt{\frac{K + \tfrac{4}{3}\mu}{\rho}}, \qquad V_S = \sqrt{\frac{\mu}{\rho}}$$- P (primary, compressional, longitudinal) waves: particle motion along the propagation direction. Always the fastest body wave.
- S (secondary, shear, transverse) waves: particle motion perpendicular to propagation. Split into SV (motion in the vertical plane containing the ray) and SH (horizontal motion). No S waves in fluids (\(\mu = 0\)).
- Poisson’s ratio \(\sigma\) links the two speeds:
A “Poisson solid” has \(\sigma = 0.25\) and \(V_P/V_S = \sqrt{3}\). A fluid has \(\sigma = 0.5\). Gas in pore space lowers \(V_P\) sharply but barely changes \(V_S\), so it lowers \(V_P/V_S\) and \(\sigma\), which is the physical root of AVO.
- Surface waves: Rayleigh waves (retrograde elliptical motion in the vertical plane, speed a little below \(V_S\); about \(0.92V_S\) for a Poisson solid) and Love waves (SH motion, need a low-velocity surface layer; dispersive). In exploration the Rayleigh wave is ground roll, the main coherent noise on land records (see Sources, Detectors and Noise).
Representative P-wave velocities
Values are approximate ranges of the kind tabulated in standard texts such as Kearey, Brooks and Hill; real rocks vary with porosity, pressure and fluid.
| Material | \(V_P\) (km/s) |
|---|---|
| Air | about 0.33 |
| Dry sand, soil | 0.2–1.0 |
| Water | about 1.45–1.5 |
| Water-saturated sand | 1.5–2.0 |
| Sandstone | 2.0–6.0 |
| Limestone | 2.0–6.0 |
| Rock salt | 4.5–5.0 |
| Granite | 5.5–6.0 |
| Gabbro | 6.5–7.0 |
| Ultramafic rocks | 7.5–8.5 |
Two rules hold almost everywhere: velocity rises with compaction and depth, and the water table shows up as a jump to about 1.5 km/s or more in unconsolidated sediment, a classic shallow-refraction target.
Acoustic impedance
$$Z = \rho V$$Impedance, not velocity alone, controls how much energy reflects at normal incidence. With \(\rho\) in g/cm³ and \(V\) in km/s, \(Z\) comes out in units of \(10^6\ \mathrm{kg\,m^{-2}\,s^{-1}}\), a handy shortcut in numericals.
Huygens, Fermat and Snell’s Law
Huygens’ principle: every point on a wavefront acts as a secondary source; the new wavefront is the envelope of the secondary wavelets. It explains refraction, diffraction and the head wave.
Fermat’s principle: a ray follows the path of stationary (usually minimum) travel time between two points.
Applying Fermat to a ray crossing a plane boundary between media of velocities \(V_1\) and \(V_2\) gives Snell’s law:
$$\boxed{\frac{\sin i_1}{V_1} = \frac{\sin i_2}{V_2} = p}$$Angles are measured from the normal to the interface. The constant \(p\) is the ray parameter (horizontal slowness, s/m). In a stack of horizontal layers \(p\) is conserved along the whole ray, and on a travel-time curve
$$p = \frac{dT}{dX}$$so the slope of a travel-time curve at any distance gives \(p\), and its reciprocal is the apparent velocity \(V_a = V/\sin i\) along the surface.
Critical angle and head waves
If \(V_2 > V_1\), the refracted ray bends away from the normal. At the critical angle \(i_c\) the refracted ray grazes the interface:
$$\sin i_c = \frac{V_1}{V_2}$$The grazing wave travels along the top of the lower medium at \(V_2\) and, by Huygens, sheds energy back into the upper layer at \(i_c\). This head wave (refracted wave, critically refracted wave) is what seismic refraction surveys time. It exists only beyond the critical distance \(x_{crit} = 2h\tan i_c\) for a layer of thickness \(h\), and it becomes the first arrival beyond the crossover distance (derivations in Refraction and Reflection Interpretation).
Beyond \(i_c\) the P reflection is total (wide-angle or post-critical reflection): its amplitude is large and its phase changes with angle.
Mode conversion and the generalised Snell’s law
At a solid–solid interface, an incident P wave at oblique incidence generates four waves: reflected P, reflected SV, transmitted P, transmitted SV. An incident SV does the same. All obey one ray parameter:
$$\frac{\sin i_1}{V_{P1}} = \frac{\sin j_1}{V_{S1}} = \frac{\sin i_2}{V_{P2}} = \frac{\sin j_2}{V_{S2}} = p$$where \(i\) are P angles and \(j\) are S angles.
- Because \(V_S < V_P\), converted S waves leave at smaller angles than the P waves on the same side.
- An incident SH wave in a horizontally layered isotropic medium produces only reflected and transmitted SH: there is no coupling to P or SV.
- At normal incidence there is no conversion: only P in, P reflected and P transmitted.
- A second critical angle exists for the transmitted SV when \(V_{S2} > V_{P1}\): \(\sin i = V_{P1}/V_{S2}\). Beyond it no wave of any kind is transmitted into the lower medium.
- At a fluid–solid interface (sea floor), an incident P in water gives reflected P in water, transmitted P and transmitted SV in the rock; no reflected S, since water cannot carry it.
graph TD
I["Incident P
angle i1"] --> RP["Reflected P
angle i1"]
I --> RS["Reflected SV
angle j1 smaller than i1"]
I --> TP["Transmitted P
angle i2"]
I --> TS["Transmitted SV
angle j2"]
RP --> N["All share p = sin i / V"]
RS --> N
TP --> N
TS --> NRay Theory
From the wave equation to rays
For a scalar potential \(\phi\) in a medium of slowly varying velocity \(V(\mathbf{x})\),
$$\nabla^2\phi = \frac{1}{V^2}\frac{\partial^2\phi}{\partial t^2}$$Try a high-frequency solution \(\phi = A(\mathbf{x})\,e^{i\omega[t - T(\mathbf{x})]}\). Collecting terms in \(\omega^2\) (dominant at high frequency) gives the eikonal equation
$$\boxed{\lvert\nabla T\rvert^2 = \frac{1}{V^2(\mathbf{x})}}$$and the terms in \(\omega\) give the transport equation \(2\nabla A\cdot\nabla T + A\nabla^2 T = 0\), which controls amplitude along the ray. Rays are the curves everywhere normal to the wavefronts \(T = \text{const}\).
Validity. Ray theory is an asymptotic, high-frequency approximation. It works when the wavelength is much smaller than the scale over which velocity changes and than the radius of curvature of interfaces. It fails at caustics, near critical angles (head waves need extra terms), in shadow zones and wherever diffraction matters. Full-waveform methods (finite differences, reflectivity) take over there.
Rays in a velocity gradient
If velocity increases linearly with depth, \(V(z) = V_0 + kz\), rays are circular arcs. A ray leaving the surface with ray parameter \(p\):
- turns (becomes horizontal) at the depth where \(V(z) = 1/p\);
- has radius \(R = 1/(pk)\);
- returns to the surface at distance \(X = 2R\cos i_0\), where \(i_0\) is the take-off angle.
These diving (turning) waves are the basis of refraction tomography in compacting sediments.
Geometrical spreading and absorption
- Spherical divergence: energy on a spherical wavefront spreads over \(4\pi r^2\), so energy falls as \(1/r^2\) and amplitude as \(1/r\). Processing undoes this with a gain function (see Seismic Data Processing).
- Absorption (intrinsic attenuation): \(A = A_0 e^{-\alpha r}\), with
where \(Q\) is the quality factor. Attenuation per wavelength is constant for constant \(Q\), so high frequencies die first: the dominant frequency of reflections falls with depth, and vertical resolution falls with it.
Fresnel zone and resolution
A reflection is not returned from a point. Energy reflected within the first Fresnel zone, the part of the reflector whose two-way path differs from the shortest path by less than half a wavelength, adds constructively. For a zero-offset source-receiver at height \(z\) above a flat reflector and wavelength \(\lambda\):
$$r_F \approx \sqrt{\frac{z\lambda}{2}} = \frac{V}{2}\sqrt{\frac{t_0}{f}}$$where \(t_0\) is two-way time and \(f\) the dominant frequency. Features smaller than \(r_F\) are not resolved laterally on unmigrated data. Migration shrinks the Fresnel zone to a small fraction of a wavelength; 2D migration does so only along the line, and only 3D migration shrinks it in both horizontal directions.
Vertical resolution. Two reflections from the top and base of a bed interfere. They can be separated down to a thickness of about \(\lambda/4\) (the tuning thickness). Below that the composite amplitude depends on thickness rather than on the impedance contrast alone: the bed can be detected but not resolved.
Reflection and Transmission Coefficients
Normal incidence
For a plane P wave hitting a plane interface at normal incidence, from medium 1 (impedance \(Z_1\)) into medium 2 (\(Z_2\)):
$$\boxed{R = \frac{Z_2 - Z_1}{Z_2 + Z_1}}, \qquad T = \frac{2Z_1}{Z_2 + Z_1}$$These are amplitude ratios with the usual exploration convention (positive \(R\) when impedance increases downwards; \(T\) here is the displacement-amplitude ratio). Energy ratios:
$$E_R = R^2, \qquad E_T = \frac{4Z_1Z_2}{(Z_1 + Z_2)^2}, \qquad E_R + E_T = 1$$- \(R\) lies between −1 and +1. Typical sedimentary contrasts give \(|R|\) of a few hundredths to about 0.2, so most energy is transmitted, which is why deep reflections are possible at all.
- Negative \(R\) (impedance decreases downwards, e.g. shale over gas sand) means the reflected wavelet is polarity-reversed relative to a positive reflection.
- Free surface (rock or water to air, \(Z_2 \approx 0\)): for an upgoing pressure wave in water, \(R \approx -1\). This generates ghosts and multiples.
- For small contrasts: \(R \approx \tfrac{1}{2}\,\Delta Z/Z = \tfrac{1}{2}\left(\Delta V/V + \Delta\rho/\rho\right)\), with \(\Delta\) the change across the interface and the bar values averages.
Reflectivity series and synthetic seismograms. Sonic (velocity) and density logs (see Porosity Logs: Sonic, Density, Neutron and Gamma Ray) give \(Z(z)\); converting depth to two-way time and computing \(R\) at each step gives the reflectivity series \(r(t)\). Convolving \(r(t)\) with a wavelet gives a synthetic seismogram for tying wells to seismic, the convolutional model used throughout processing.
Oblique incidence: the Zoeppritz equations
At a welded solid–solid interface, four boundary conditions must hold at every point and time:
| Condition | Physical meaning |
|---|---|
| Continuity of normal displacement | No gap opens, no interpenetration |
| Continuity of tangential displacement | No slip (welded contact) |
| Continuity of normal stress | Newton’s third law across the interface |
| Continuity of shear stress | Same, for tangential traction |
For an incident P wave of unit amplitude there are four unknowns: amplitudes of reflected P (\(R_{PP}\)), reflected SV (\(R_{PS}\)), transmitted P (\(T_{PP}\)) and transmitted SV (\(T_{PS}\)). The four boundary conditions give four linear equations (the Zoeppritz equations) in these unknowns. Their coefficients depend on \(V_{P1}, V_{S1}, \rho_1, V_{P2}, V_{S2}, \rho_2\) and on the incidence angle through Snell’s law. Key consequences:
- The coefficients depend on six elastic parameters, but at any angle only on contrasts and ratios; at normal incidence they collapse to the impedance formula above.
- Beyond the critical angle the coefficients become complex: total reflection with a phase shift.
- Converted waves (\(R_{PS}\)) are zero at normal incidence and grow with angle.
- At a fluid–solid interface the tangential conditions drop out (a fluid cannot sustain shear stress and may slip), leaving fewer equations and unknowns.
The exact equations are cumbersome, so interpreters use linear approximations valid for small contrasts and angles below about 30°–40°.
Aki–Richards and Shuey approximations
Aki–Richards (small contrasts, \(\theta\) the average of incidence and transmission angles, \(p\) the ray parameter):
$$R_{PP}(\theta) \approx \frac{1}{2}\left(1 - 4p^2V_S^2\right)\frac{\Delta\rho}{\rho} + \frac{1}{2\cos^2\theta}\frac{\Delta V_P}{V_P} - 4p^2V_S^2\frac{\Delta V_S}{V_S}$$Shuey’s rearrangement groups terms by angle:
$$\boxed{R(\theta) \approx A + B\sin^2\theta + C\left(\tan^2\theta - \sin^2\theta\right)}$$$$A = \frac{1}{2}\left(\frac{\Delta V_P}{V_P} + \frac{\Delta\rho}{\rho}\right), \quad B = \frac{1}{2}\frac{\Delta V_P}{V_P} - 2\frac{V_S^2}{V_P^2}\left(\frac{\Delta\rho}{\rho} + 2\frac{\Delta V_S}{V_S}\right), \quad C = \frac{1}{2}\frac{\Delta V_P}{V_P}$$- \(A\) is the intercept (normal-incidence reflection coefficient).
- \(B\) is the gradient: how fast amplitude changes with angle. It carries the S-wave (Poisson’s ratio) information.
- \(C\) matters only at wide angles (beyond about 30°). The two-term form \(R \approx A + B\sin^2\theta\) is the basis of intercept–gradient AVO analysis.
Memory Tricks
Limiting-case checks.
- \(Z_1 = Z_2\): \(R = 0\), \(T = 1\). No reflection, however different the rocks look.
- \(Z_2 \to 0\) (free surface): \(R \to -1\).
- \(Z_2 \to \infty\) (rigid base): \(R \to +1\).
- \(\theta = 0\) in Shuey: \(R = A\), the normal-incidence value.
Don’t Confuse
| This | vs | That |
|---|---|---|
| First critical angle \(\sin i_c = V_{P1}/V_{P2}\): transmitted P grazes; needs \(V_{P2} > V_{P1}\) | vs | Second critical angle \(\sin i = V_{P1}/V_{S2}\): transmitted SV grazes; needs \(V_{S2} > V_{P1}\) |
| Ray parameter \(p = \sin i/V\) (s/m) | vs | Apparent velocity \(V_a = 1/p = V/\sin i\) (m/s) |
| Acoustic impedance \(\rho V_P\): controls normal-incidence \(R\) | vs | Velocity alone: controls angles (Snell), not amplitude |
| Amplitude coefficient \(R\) | vs | Energy coefficient \(R^2\) |
| Head wave: travels along the interface at \(V_2\) | vs | Wide-angle reflection: reflects back at \(V_1\), arrives later |
| Intercept \(A\): normal incidence | vs | Gradient \(B\): change with \(\sin^2\theta\), sensitive to \(V_S\) |
| Fresnel zone: lateral resolution | vs | Tuning thickness \(\lambda/4\): vertical resolution |
| Spherical divergence: frequency-independent, \(1/r\) | vs | Absorption: frequency-dependent, \(e^{-\pi f r/(QV)}\) |
Common Mistakes
Practice
All questions below are original practice questions written in CSIR NET Part C (Geophysics) style. They are not previous-year questions.
Level 1: Foundation
- A layer with \(V_1 = 1500\) m/s overlies one with \(V_2 = 3000\) m/s. What is the critical angle?
- Two layers have equal acoustic impedance but different velocities. What is the normal-incidence reflection coefficient?
- An SH wave strikes a horizontal interface between two isotropic solids. Which waves are generated?
Answers
- \(\sin i_c = 1500/3000 = 0.5\), so \(i_c = 30°\).
- Zero. \(R = (Z_2 - Z_1)/(Z_2 + Z_1) = 0\); the velocity change still bends oblique rays.
- Reflected SH and transmitted SH only. SH does not couple to P or SV in this geometry.
Level 2: Part B Style
Q1 (practice). A P wave travelling at 2000 m/s meets a horizontal interface at 30° incidence. The lower layer has \(V_P = 3000\) m/s. The angle of the transmitted P wave is closest to:
- (a) 19.5°
- (b) 30.0°
- (c) 48.6°
- (d) 90°, since the angle exceeds critical
Answer and explanation
(c). \(\sin i_2 = (3000/2000)\sin 30° = 1.5 \times 0.5 = 0.75\), so \(i_2 = \sin^{-1}0.75 = 48.6°\). The critical angle is \(\sin^{-1}(2/3) = 41.8°\), so 30° is below critical and a transmitted wave exists. Option (a) is what you get by inverting the velocity ratio.
Q2 (practice). Layer 1: \(V = 2000\) m/s, \(\rho = 2000\) kg/m³. Layer 2: \(V = 3000\) m/s, \(\rho = 2400\) kg/m³. At normal incidence, the fraction of incident energy reflected is about:
- (a) 29%
- (b) 8.2%
- (c) 71%
- (d) 0.8%
Answer and explanation
(b). \(Z_1 = 4.0\times10^6\), \(Z_2 = 7.2\times10^6\ \mathrm{kg\,m^{-2}s^{-1}}\). \(R = 3.2/11.2 = 0.286\). Energy \(R^2 = 0.0816\), about 8.2%. Option (a) is the amplitude coefficient, not energy. Check: \(E_T = 4(4.0)(7.2)/(11.2)^2 = 115.2/125.44 = 0.918\); \(0.082 + 0.918 = 1\).
Q3 (practice). A reflector lies at two-way time 2.0 s in a medium of velocity 3000 m/s. The dominant frequency is 30 Hz. The radius of the first Fresnel zone (unmigrated, zero offset) and the tuning thickness are approximately:
- (a) 387 m and 25 m
- (b) 194 m and 100 m
- (c) 775 m and 25 m
- (d) 387 m and 100 m
Answer and explanation
(a). \(r_F = (V/2)\sqrt{t_0/f} = 1500\sqrt{2/30} = 1500 \times 0.258 = 387\) m. Wavelength \(\lambda = V/f = 100\) m, so tuning thickness \(\lambda/4 = 25\) m. Same answer from \(r_F = \sqrt{z\lambda/2}\) with \(z = 3000\) m: \(\sqrt{150{,}000} = 387\) m.
Q4 (practice). Which statement about ray theory is correct?
- (a) It is exact for any frequency in a layered medium.
- (b) It follows from the high-frequency limit of the wave equation, giving the eikonal equation \(\lvert\nabla T\rvert^2 = 1/V^2\).
- (c) It predicts diffractions from faults correctly at all frequencies.
- (d) It requires the wavelength to be large compared with layer thicknesses.
Answer and explanation
(b). Ray theory is the leading term of an asymptotic expansion in \(1/\omega\). It needs wavelengths small compared with the scale of heterogeneity (so (d) is reversed) and is inadequate for diffraction and head-wave amplitudes.
Level 3: Part C Style
Q1 (practice). A shale (\(V_P = 2.70\) km/s, \(V_S = 1.25\) km/s, \(\rho = 2.40\) g/cm³) overlies a gas sand (\(V_P = 2.40\) km/s, \(V_S = 1.50\) km/s, \(\rho = 2.10\) g/cm³). Using the two-term Shuey approximation with average properties:
(i) Find the intercept \(A\) and compare it with the exact normal-incidence \(R\). (ii) Find the gradient \(B\). (iii) Estimate \(R\) at 30°. (iv) Does the amplitude magnitude increase or decrease with angle?
Answer and worked solution
Averages and contrasts. \(\bar V_P = 2.55\), \(\Delta V_P = -0.30\) → \(\Delta V_P/V_P = -0.1176\). \(\bar V_S = 1.375\), \(\Delta V_S = +0.25\) → \(\Delta V_S/V_S = +0.1818\). \(\bar\rho = 2.25\), \(\Delta\rho = -0.30\) → \(\Delta\rho/\rho = -0.1333\). \((V_S/V_P)^2 = (1.375/2.55)^2 = 0.2908\).
- \(A = \tfrac12(-0.1176 - 0.1333) = -0.1255\). Exact: \(Z_1 = 6.48\), \(Z_2 = 5.04\), \(R_0 = -1.44/11.52 = -0.125\). The linear approximation is excellent for this small contrast.
- \(B = \tfrac12(-0.1176) - 2(0.2908)(-0.1333 + 2\times0.1818) = -0.0588 - 0.5815\times0.2303 = -0.0588 - 0.1339 = -0.1927\).
- At 30°, \(\sin^2\theta = 0.25\): \(R \approx -0.1255 + 0.25(-0.1927) = -0.1737\).
- \(A < 0\) and \(B < 0\): the reflection becomes more negative with angle, so its magnitude increases. A negative intercept with a negative gradient is the AVO behaviour of a low-impedance gas sand (Class III, see the AVO page).
Q2 (practice). Layer 1: \(V_P = 2000\) m/s, \(V_S = 1000\) m/s. Layer 2: \(V_P = 4000\) m/s, \(V_S = 2300\) m/s. Consider these statements:
(A) The P-wave critical angle is 30°. (B) For P incidence beyond about 60.4°, no wave of any kind is transmitted into layer 2. (C) For P incident at 30°, the reflected SV leaves at a larger angle than 30°. (D) At normal incidence, no converted waves are produced.
Which are correct?
- (a) A, B and D only
- (b) A and C only
- (c) B, C and D only
- (d) A, B, C and D
Answer and worked solution
(a) A, B and D.
- (A) \(\sin i_c = 2000/4000 = 0.5\) → 30°. Correct.
- (B) Transmitted SV becomes critical when \(\sin i_1 = V_{P1}/V_{S2} = 2000/2300 = 0.8696\) → \(i_1 = 60.4°\). Beyond this, both transmitted P (critical at 30°) and transmitted SV are evanescent. Correct.
- (C) \(\sin j_1 = (V_{S1}/V_{P1})\sin 30° = 0.5\times0.5 = 0.25\) → \(j_1 = 14.5°\), smaller than 30°. Wrong.
- (D) Correct: conversion requires oblique incidence.
Q3 (practice). Velocity increases linearly with depth as \(V(z) = 2000 + 0.5z\) (m/s, \(z\) in m). A P ray leaves the surface at 30° from the vertical. Find (i) the ray parameter, (ii) the depth at which the ray turns, (iii) the radius of the circular ray path and (iv) the distance at which it re-emerges at the surface.
Answer and worked solution
- \(p = \sin 30°/2000 = 2.5\times10^{-4}\) s/m.
- The ray is horizontal where \(V = 1/p = 4000\) m/s: \(2000 + 0.5z = 4000\) → \(z = 4000\) m.
- \(R = 1/(pk) = 1/(2.5\times10^{-4}\times0.5) = 8000\) m.
- \(X = 2R\cos i_0 = 2(8000)(0.866) = 13{,}856\) m, about 13.9 km.
Geometric check: the circle’s centre lies at height \(V_0/k = 4000\) m above the surface. Its lowest point is \(8000 - 4000 = 4000\) m deep, matching (ii); its chord at the surface is \(2\sqrt{8000^2 - 4000^2} = 13{,}856\) m, matching (iv).
Quick Revision Table
| Item | Fact |
|---|---|
| \(V_P\), \(V_S\) | \(\sqrt{(K + 4\mu/3)/\rho}\), \(\sqrt{\mu/\rho}\); no S in fluids |
| Poisson solid | \(\sigma = 0.25\), \(V_P/V_S = \sqrt3\) |
| Snell | \(\sin i_1/V_1 = \sin i_2/V_2 = p\); angles from the normal |
| Ray parameter | \(p = dT/dX\); conserved in flat layers |
| Critical angle | \(\sin i_c = V_1/V_2\); needs \(V_2 > V_1\) |
| Mode conversion | P → RP, RS, TP, TS; none at normal incidence; SH stays SH |
| Eikonal | \(\lvert\nabla T\rvert^2 = 1/V^2\); high-frequency limit |
| Gradient medium | Circular rays; \(R = 1/(pk)\); turns where \(V = 1/p\) |
| Spreading / absorption | Amplitude \(\propto 1/r\); \(\alpha = \pi f/(QV)\) |
| Fresnel zone | \(r_F \approx \sqrt{z\lambda/2} = (V/2)\sqrt{t_0/f}\) |
| Tuning | \(\lambda/4\) |
| Normal incidence | \(R = (Z_2 - Z_1)/(Z_2 + Z_1)\); \(T = 2Z_1/(Z_1 + Z_2)\) |
| Energy | \(R^2 + 4Z_1Z_2/(Z_1 + Z_2)^2 = 1\) |
| Free surface | \(R \approx -1\) for upgoing pressure in water |
| Zoeppritz | 4 boundary conditions → 4 equations → RP, RS, TP, TS |
| Shuey | \(R \approx A + B\sin^2\theta + C(\tan^2\theta - \sin^2\theta)\) |
Key Takeaways
What’s Next
- Seismic Sources, Detectors and Noise — how the wavefield is generated and recorded, and what contaminates it.
- Refraction and Reflection Interpretation — travel-time equations built on Snell’s law.
- Bright Spots, AVO, VSP, 3D and Seismic Stratigraphy — Shuey’s intercept and gradient put to work.
- Quick Revision — the whole unit on one page.