Skip to content

Earthquake Sources, Moment Tensor and Focal Mechanisms

CSIR NET geophysics: double-couple source, seismic moment, moment tensor decomposition, radiation patterns, source spectra, stress drop, fault-plane solutions.

  • 21 min read
  • Updated
On this page · 15 sections
  1. Prerequisites
  2. The Hook: Two Forces Are Not Enough
  3. Kinematic Description of a Fault Source
  4. The Moment Tensor
  5. Radiation Patterns
  6. Fault-Plane Solutions from First Motions
  7. Source Spectrum, Corner Frequency and Stress Drop
  8. Finite Rupture: Duration and Directivity
  9. Memory Tricks
  10. Don’t Confuse
  11. Common Mistakes
  12. Practice
  13. Quick Revision Table
  14. Key Takeaways
  15. What’s Next

Prerequisites

The Hook: Two Forces Are Not Enough


Kinematic Description of a Fault Source

A tectonic earthquake is a shear dislocation: the two sides of a fault surface \( \Sigma \) slip past each other by a displacement discontinuity \( \mathbf{D} \) (the slip vector), which lies in the fault plane. Seismology describes the source by equivalent body forces that would radiate the same waves in an unfaulted medium.

Geometric quantitySymbolMeaning
Fault normal\( \hat{\mathbf n} \)unit vector perpendicular to the fault, pointing towards the hanging-wall (positive) side
Slip direction\( \hat{\mathbf d} \)direction in which the positive side moves relative to the negative side
Strike \( \phi_s \)0–360°azimuth of the fault trace, measured clockwise from north, with the fault dipping to the right when looking along strike
Dip \( \delta \)0–90°angle of the plane below the horizontal
Rake \( \lambda \)−180° to 180°angle in the fault plane from the strike direction to the slip vector of the hanging wall

Rake conventions (Aki and Richards):

RakeFaulting
0°left-lateral strike-slip
±180°right-lateral strike-slip
+90°pure thrust (reverse)
−90°pure normal
between 0 and 180reverse component; between 0 and −180, normal component

Seismic moment

The scalar seismic moment is the strength of each couple of the double couple:

$$\boxed{M_0 = \mu A \bar D}$$

with \( \mu \) the rigidity of the source region, \( A \) the rupture area and \( \bar D \) the average slip. It is measured from the long-period amplitude of the waves (the flat part of the source spectrum, below) and gives the moment magnitude:

$$\boxed{M_w = \frac{2}{3}\left(\log_{10}M_0 - 9.1\right)}\qquad (M_0\ \text{in N m})$$

Inverting: \( M_0 = 10^{1.5M_w + 9.1} \) N m. One unit of \( M_w \) is a factor of \( 10^{1.5} \approx 31.6 \) in moment; 0.2 units is a factor of 2.

The Moment Tensor

A general point source of seismic waves (with no net force or torque) is described by a symmetric second-order moment tensor \( M_{ij} \). The far-field displacement is a linear combination of its six independent components, so \( M_{ij} \) can be found by linear inversion of waveforms; that is how modern catalogues (such as the Global CMT project’s centroid moment tensors) are made.

For a shear dislocation,

$$\boxed{M_{ij} = M_0\,(\hat n_i\hat d_j + \hat n_j\hat d_i)}$$

Because \( \hat{\mathbf n} \) and \( \hat{\mathbf d} \) enter symmetrically, swapping them (fault plane ↔ auxiliary plane) gives the same tensor. That is the fault-plane ambiguity in one line.

Eigenvalues and principal axes

For a pure double couple the eigenvalues are

$$\lambda = (+M_0,\ 0,\ -M_0)$$
EigenvectorEigenvalueAxisRelation to the fault
\( (\hat{\mathbf n} + \hat{\mathbf d})/\sqrt 2 \)\( +M_0 \)T axis (tension)45° from both nodal planes, in the compressional first-motion quadrant
\( (\hat{\mathbf n} - \hat{\mathbf d})/\sqrt 2 \)\( -M_0 \)P axis (pressure)45° from both nodal planes, in the dilatational quadrant
\( \hat{\mathbf n}\times\hat{\mathbf d} \)0B (null) axisintersection line of the two nodal planes

The P and T axes are often taken as estimates of the principal stress directions \( \sigma_1 \) and \( \sigma_3 \), but this is an approximation: a fault that slips may be a pre-existing weak plane not at 45° to \( \sigma_1 \). Inversions of many mechanisms for a regional stress tensor are better than a single mechanism.

Decomposition: isotropic, double couple and CLVD

Any moment tensor splits into an isotropic part and a deviatoric part:

$$M_{ij} = \tfrac13 M_{kk}\,\delta_{ij} + M'_{ij}$$
  • The isotropic part \( M_{kk}/3 \) represents volume change: positive for explosions, negative for implosions (for example, some deep-mine collapses).
  • The deviatoric part, with eigenvalues \( m_1, m_2, m_3 \) summing to zero, is further split into a double couple (DC) and a compensated linear vector dipole (CLVD): a dipole of strength \( 2 \) along one axis balanced by dipoles of strength \( -1 \) along the other two, with no volume change.

A common measure of non-DC content uses the deviatoric eigenvalues ordered by absolute value, \( |m_{min}| \le |m_{int}| \le |m_{max}| \):

$$\boxed{\varepsilon = -\frac{m_{min}}{|m_{max}|}}$$
\( \varepsilon \)Source
0pure double couple (eigenvalues \( M_0, 0, -M_0 \))
±0.5pure CLVD (eigenvalues in ratio 2 : −1 : −1)
betweenmixture; percentage DC \( \approx (1 - 2\lvert\varepsilon\rvert)\times 100 \)

Non-double-couple sources to recognise: explosions and cavity collapses (isotropic); volcanic events, ring-fault slip and magma-filled crack opening (CLVD and isotropic parts); tensile cracks in geothermal and injection settings; and complex ruptures on several faults with different orientations, which sum to an apparent non-DC tensor. Small non-DC percentages are often just noise and modelling error.

Radiation Patterns

For a double couple in a homogeneous medium, the far-field displacement at distance \( r \) is (Aki and Richards form):

$$\mathbf u^P = \frac{1}{4\pi\rho\alpha^3}\,\frac{1}{r}\,\dot M_0\!\left(t - \frac r\alpha\right)\,\sin 2\theta\cos\phi\;\hat{\mathbf r}$$$$\mathbf u^S = \frac{1}{4\pi\rho\beta^3}\,\frac{1}{r}\,\dot M_0\!\left(t - \frac r\beta\right)\left(\cos 2\theta\cos\phi\;\hat{\boldsymbol\theta} - \cos\theta\sin\phi\;\hat{\boldsymbol\phi}\right)$$

with \( \theta \) measured from the fault normal, \( \phi \) from the slip direction in the fault plane, \( \alpha \) and \( \beta \) the P and S velocities.

What to read from these:

  1. Far-field displacement is proportional to the moment rate \( \dot M_0(t) \): a step in moment gives a pulse of displacement. The pulse duration is the source duration.
  2. P radiation has four lobes with alternating sign; it is zero on both nodal planes (the fault plane and the auxiliary plane). Maximum P amplitude lies along the P and T axes, 45° from the planes.
  3. S radiation is maximum on the nodal planes where P is zero, and zero along the P, T and B axes.
  4. Far-field S is larger than P by about \( (\alpha/\beta)^3 \). For a Poisson solid, \( \alpha/\beta = \sqrt3 \) and the factor is about 5.2.
  5. Amplitudes fall as \( 1/r \) (geometric spreading of body waves in a whole space), before attenuation.

Near-field terms decay faster (as \( 1/r^2 \) and \( 1/r^4 \)) and record the permanent static displacement close to the fault; they are what GPS and InSAR measure.

Fault-Plane Solutions from First Motions

Procedure

  1. For each station, pick the polarity of the first P motion: up (compression, C) or down (dilatation, D) on the vertical component.
  2. Compute the ray’s azimuth from source to station and its take-off angle \( i_h \) at the source (from the velocity model, using \( p = \sin i_h/v_h \)).
  3. Plot each polarity on a lower-hemisphere stereographic (Wulff) or equal-area (Schmidt) projection of the focal sphere.
  4. Fit two orthogonal great circles (the nodal planes) that separate compressions from dilatations.
  5. Read the strike and dip of each plane. The pole of each plane is the slip vector of the other. P lies in the middle of the dilatational quadrants, T in the middle of the compressional ones, both 45° from the planes; B is where the planes intersect.

Take-off angles are measured from the downward vertical. A ray that leaves the source upward (take-off angle greater than 90°, common for nearby stations above a deep focus) is plotted on the lower hemisphere at the antipodal point: azimuth + 180° and take-off angle 180° − \( i_h \). Its polarity is unchanged, because the radiation pattern is symmetric through the source.

Other data that constrain mechanisms: S-wave polarisation directions, amplitude ratios (S/P, SH/SV), and full waveform inversion for the moment tensor (works with fewer stations and gives \( M_0 \) at the same time).

Reading beach balls

MechanismLower-hemisphere patternP axisT axisRake
Thrustcompressional (shaded) centrehorizontalverticalabout +90°
Normaldilatational (white) centreverticalhorizontalabout −90°
Strike-slipfour quadrants, both planes vertical (a cross)horizontalhorizontalabout 0° or 180°
Obliqueasymmetricinclinedinclinedintermediate

Source Spectrum, Corner Frequency and Stress Drop

The \( \omega^2 \) model

Real ruptures have finite size and duration. The far-field displacement spectrum of a body wave is, to a good approximation (the omega-squared model of Aki and of Brune):

$$|\Omega(f)| = \frac{\Omega_0}{1 + (f/f_c)^2}$$
  • Below the corner frequency \( f_c \): flat, with level \( \Omega_0 \propto M_0 \). This is where \( M_0 \) is measured.
  • Above \( f_c \): falls as \( f^{-2} \).
  • \( f_c \) is inversely proportional to the source dimension (and duration). Bigger earthquakes have lower corner frequencies.

This is also why amplitude magnitudes saturate: \( m_b \) is read at about 1 s and \( M_s \) at about 20 s. Once \( f_c \) drops below the measurement frequency, the amplitude there stops growing in proportion to \( M_0 \).

Brune’s model

For a circular fault of radius \( r \), Brune related the S-wave corner frequency to the radius:

$$\boxed{r = \frac{2.34\,\beta}{2\pi f_c} \approx \frac{0.37\,\beta}{f_c}}$$

and the static stress drop for a circular crack (Eshelby) is

$$\boxed{\Delta\sigma = \frac{7}{16}\,\frac{M_0}{r^3}}$$

Typical earthquake stress drops lie between about 0.1 and 100 MPa, with many in the 1–10 MPa range, and are roughly independent of size. Constant stress drop implies self-similar scaling: \( M_0 \propto r^3 \propto f_c^{-3} \), so \( \log M_0 \) increases by 3 when \( \log f_c \) decreases by 1.

General form for any shape: \( \Delta\sigma = C\mu\bar D/\tilde L \), with \( \tilde L \) a characteristic dimension (radius or width) and \( C \) a shape factor; for a circular crack, \( C = 7\pi/16 \).

Energy and apparent stress

  • Radiated seismic energy \( E_s \) is measured by integrating the squared velocity spectrum, so it depends on the high frequencies above \( f_c \).
  • Apparent stress \( \sigma_a = \mu E_s/M_0 \) links energy and moment. Kanamori’s \( M_w \) was built on the assumption \( E_s/M_0 \approx 5\times10^{-5} \), which follows from \( E_s \approx (\Delta\sigma/2\mu)M_0 \) with \( \Delta\sigma \) about 3 MPa and \( \mu \) about \( 3\times10^{10} \) Pa.
  • The energy magnitude \( M_e \) is computed from \( E_s \); it can differ from \( M_w \) for events with unusual stress drop or slow rupture.

Finite Rupture: Duration and Directivity

A rupture of length \( L \) propagating at rupture velocity \( v_r \) (typically about 0.7–0.9 of \( \beta \)) lasts about \( L/v_r \). For unilateral rupture, a station at angle \( \psi \) from the rupture direction sees the pulse duration

$$\boxed{\tau(\psi) = \frac{L}{v_r} - \frac{L}{c}\cos\psi}$$

where \( c \) is the wave speed (P or S). In the rupture direction (\( \psi = 0 \)) the pulse is short and large (energy arrives compressed, like a Doppler effect); behind the rupture (\( \psi = 180° \)) it is long and small. The area under the displacement pulse (proportional to \( M_0 \)) is the same at all azimuths. This directivity explains asymmetric damage around many large earthquakes.

Other finite-source terms: rise time (time for slip at one point to complete), source time function (moment rate against time), slip distribution (from inversion of seismic, geodetic and tsunami data), asperities (high-slip patches) and barriers. Very large ruptures, such as megathrust events, last minutes; this is why \( M_w \) must be computed from very long periods or the W phase for great earthquakes.


Memory Tricks

Don’t Confuse

ThisvsThat
Single couple: net torque, wrong S patternDouble couple: no net torque, equivalent to shear slip
Fault planeAuxiliary plane: identical radiation; needs geology, aftershocks or directivity to resolve
P axis (compression, eigenvalue \( -M_0 \))T axis (tension, eigenvalue \( +M_0 \))
P and T axes from one mechanismPrincipal stresses \( \sigma_1, \sigma_3 \): only approximately aligned
Isotropic component: volume changeCLVD: no volume change, dipole 2 : −1 : −1
Static stress drop \( \Delta\sigma \) (from \( M_0 \) and size)Apparent stress \( \mu E_s/M_0 \) (from radiated energy)
Corner frequency: source sizeInstrument natural frequency: sensor property
Hypocentre: where rupture starts (first arrivals)Centroid: moment-weighted average location (CMT)
Rupture velocity \( v_r \) (below \( \beta \) usually)Slip velocity (particle velocity of fault faces, about m/s)

Common Mistakes


Practice

All questions below are original practice questions written for this page. They are not from any CSIR NET paper.

Level 1: Foundation

  1. Give the eigenvalues of a pure double-couple moment tensor of scalar moment \( M_0 \).
  2. What rake describes pure normal faulting?
  3. In which quadrant of a beach ball does the T axis lie?
Answers
  1. \( +M_0,\ 0,\ -M_0 \).
  2. −90°.
  3. The compressional (shaded) quadrant.

Level 2: Part B Style

Practice Q1. A rupture of 40 km × 15 km with average slip 1.0 m in crust of rigidity \( 3\times10^{10} \) Pa has a moment magnitude of about:

(a) 5.8 (b) 6.4 (c) 6.8 (d) 7.4

Answer: (c) 6.8

\( A = 4\times10^4\times1.5\times10^4 = 6\times10^8 \) m² (600 km²). \( M_0 = 3\times10^{10}\times6\times10^8\times1.0 = 1.8\times10^{19} \) N m.

\( \log_{10}M_0 = 19.255 \); \( M_w = \frac23(19.255 - 9.1) = \frac23(10.155) = 6.77 \).

Using the area in km² (600) instead of m² gives an absurdly small moment; always convert to SI first.

Practice Q2. Which moment tensor (eigenvalues, same units) is closest to a pure explosion?

(a) \( (1, 0, -1) \) (b) \( (2, -1, -1) \) (c) \( (3, 3, 3) \) (d) \( (5, -1, -4) \)

Answer: (c)

Equal positive eigenvalues mean a purely isotropic expansion. (a) is a pure DC, (b) a pure CLVD, (d) a deviatoric DC + CLVD mixture.

Practice Q3. For a double-couple source, which statement about far-field radiation is correct?

(a) P amplitude is maximum on the fault plane. (b) S amplitude is zero on the nodal planes. (c) P amplitude is zero on both nodal planes and maximum along the P and T axes. (d) P and S have the same maximum amplitude for the same moment rate.

Answer: (c)

\( \sin2\theta\cos\phi \) vanishes on both planes and peaks at 45°. S peaks on the planes; far-field S is about \( (\alpha/\beta)^3 \approx 5 \) times larger than P.

Practice Q4. The S-wave corner frequency of an earthquake is 0.5 Hz and \( \beta = 3.6 \) km/s. The Brune source radius is about:

(a) 0.67 km (b) 1.3 km (c) 2.7 km (d) 7.2 km

Answer: (c) 2.7 km

\( r = 2.34\beta/(2\pi f_c) = 2.34\times3.6/(2\pi\times0.5) = 8.424/3.142 = 2.68 \) km.

Level 3: Part C Style

Practice Q5. An \( M_w \) 6.0 earthquake has a Brune radius of 4.0 km. A second earthquake in the same region has the same stress drop and \( M_w \) 7.0. Which statements are correct?

  1. The stress drop of the first event is about 8.6 MPa.
  2. The moment of the second event is about 31.6 times that of the first.
  3. The radius of the second event is about 12.6 km.
  4. The corner frequency of the second event is about one-third that of the first.

(a) 1 and 2 only (b) 2 and 3 only (c) 1, 2, 3 and 4 (d) 1, 2 and 4 only

Answer: (c) 1, 2, 3 and 4
  • \( M_0 = 10^{18.1} = 1.259\times10^{18} \) N m. \( \Delta\sigma = 0.4375\times1.259\times10^{18}/(4\times10^3)^3 = 0.4375\times1.259\times10^{18}/6.4\times10^{10} = 8.6\times10^6 \) Pa. True.
  • One unit of \( M_w \): \( 10^{1.5} = 31.6 \). True.
  • Same \( \Delta\sigma \): \( r \propto M_0^{1/3} \), so \( r_2 = 4.0\times31.6^{1/3} = 4.0\times3.16 = 12.6 \) km. True.
  • \( f_c \propto 1/r \): ratio \( 1/3.16 \approx 0.32 \), about one-third. True.

Practice Q6. A moment tensor in (x = north, y = east, z = down) coordinates is

$$\mathbf M = \begin{pmatrix}2 & 0 & 0\\ 0 & 2 & 0\\ 0 & 0 & -4\end{pmatrix}\times10^{16}\ \text{N m}$$

Which statements are correct?

  1. Its isotropic part is zero.
  2. It is a pure CLVD with \( \varepsilon = 0.5 \) in magnitude.
  3. Its major dipole is vertical with negative eigenvalue, i.e. vertical compression balanced by horizontal extension.
  4. It is a pure double couple.

(a) 1, 2 and 3 only (b) 1 and 4 only (c) 2 and 3 only (d) 4 only

Answer: (a) 1, 2 and 3 only
  • Trace \( = 2 + 2 - 4 = 0 \). True.
  • Eigenvalues \( 2, 2, -4 \): ratio 1 : 1 : −2, a CLVD. Ordered by absolute value, \( m_{min} = 2 \), \( m_{max} = -4 \): \( \varepsilon = -2/4 = -0.5 \), magnitude 0.5. True.
  • The largest-magnitude eigenvalue \( -4 \) is along z (vertical): compressional dipole vertical, balanced by tension horizontally. True. Such mechanisms are reported, for example, for some volcanic and ring-fault sources.
  • A DC needs a zero eigenvalue. False.

Practice Q7. A unilateral rupture of length 60 km propagates at 3.0 km/s. S waves travel at 3.5 km/s. Which statements are correct?

  1. The rupture lasts 20 s.
  2. A station in the rupture direction records an S pulse of about 2.9 s.
  3. A station directly behind the rupture records an S pulse of about 37 s.
  4. The area under the far-field displacement pulse is 13 times larger in the forward direction.

(a) 1, 2 and 3 only (b) 1 and 4 only (c) 2, 3 and 4 only (d) 1, 2, 3 and 4

Answer: (a) 1, 2 and 3 only
  • \( L/v_r = 60/3 = 20 \) s. True.
  • Forward: \( 20 - 60/3.5 = 20 - 17.14 = 2.86 \) s. True.
  • Backward: \( 20 + 17.14 = 37.14 \) s. True.
  • The pulse area is proportional to \( M_0 \), the same in every direction; only its height and width change (the forward pulse is about 13 times taller). False.

Quick Revision Table

IdeaFact or formula
Equivalent forcedouble couple (no net torque)
Seismic moment\( M_0 = \mu A\bar D \), N m
Moment magnitude\( M_w = \frac23(\log_{10}M_0 - 9.1) \); ×31.6 per unit; ×2 per 0.2
Shear-source tensor\( M_{ij} = M_0(n_id_j + n_jd_i) \); symmetric in \( n, d \)
DC eigenvalues\( +M_0 \) (T), 0 (B), \( -M_0 \) (P)
Decompositionisotropic \( M_{kk}/3 \) + DC + CLVD
\( \varepsilon \)\( -m_{min}/\lvert m_{max}\rvert \); 0 DC, ±0.5 CLVD; DC% ≈ \( 1 - 2\lvert\varepsilon\rvert \)
Rake0 left-lateral, 180 right-lateral, +90 thrust, −90 normal
RadiationP \( \propto \sin2\theta\cos\phi \), zero on planes; S max on planes; S/P ≈ \( (\alpha/\beta)^3 \)
Far field\( \propto \dot M_0(t - r/c)/r \)
Beach ballsthrust shaded centre; normal white centre; strike-slip cross
\( \omega^2 \) modelflat below \( f_c \) (\( \propto M_0 \)), \( f^{-2} \) above
Brune\( r = 2.34\beta/(2\pi f_c) \); \( \Delta\sigma = \frac{7}{16}M_0/r^3 \)
Stress dropabout 0.1–100 MPa, often 1–10 MPa; self-similar \( M_0 \propto f_c^{-3} \)
Apparent stress\( \sigma_a = \mu E_s/M_0 \); \( E_s/M_0 \approx 5\times10^{-5} \)
Directivity\( \tau = L/v_r - (L/c)\cos\psi \)

Key Takeaways

What’s Next