Formation Evaluation: Formation Factor, Porosity, Permeability, Saturation and Lithology
Archie's formation factor and saturation equations, Rwa and Pickett plots, moveable hydrocarbons, log permeability and lithology crossplots for CSIR NET.
- 21 min
On this page · 15 sections
Prerequisites
- Electrical, SP and Temperature Logs — where \( R_t \), \( R_{xo} \) and \( R_w \) come from, corrected to formation temperature.
- Porosity Logs: Sonic, Density, Neutron and Gamma Ray — porosity, shale volume and the matrix values used in lithology plots.
- Hydrogeology: Darcy’s Law, Aquifers, Groundwater Exploration and Pollution — Darcy’s law and hydraulic conductivity; permeability here is the same property in petroleum units.
- Petroleum Geology and Indian Basins — reservoirs, traps and the volumetric (STOIIP) equation that uses the porosity and saturation found here.
The Hook: Archie’s Cores
How CSIR NET asks it. Part C Geophysics numericals: formation factor and \( R_o \); water saturation by Archie; \( R_w \) from a water zone and the \( R_{wa} \) method; Pickett-plot slope as \( m \); flushed-zone saturation and hydrocarbon movability; bulk volume water and irreducible saturation; log-derived permeability; lithology from M–N, matrix-density and Pe plots; and statement questions on the assumptions (clean formation, shaly sands, choice of \( a \), \( m \), \( n \)).
The Workflow
graph TD
A["Quality check
caliper, depth match,
borehole corrections"] --> B["Shale volume
GR, SP, N-D separation"]
B --> C["Lithology
Pe, N-D crossplot, M-N"]
C --> D["Porosity
density, neutron, sonic
with correct matrix"]
D --> E["Rw
SP, water-zone Rwa,
Pickett plot, samples"]
E --> F["Water saturation
Archie (clean) or
shaly-sand model"]
F --> G["Movability and
permeability
Sxo, BVW, k estimate"]
G --> H["Net pay and
hydrocarbon volume
cutoffs, h phi (1 - Sw)"]Formation Factor
For a clean (clay-free) rock fully saturated with water of resistivity \( R_w \), the rock resistivity \( R_o \) is proportional to \( R_w \). The constant of proportionality is the formation (resistivity) factor:
$$\boxed{F = \frac{R_o}{R_w}}$$\( F \) depends only on the pore structure. More porosity means more conducting paths and a lower \( F \); more tortuous and more cemented pores mean a higher \( F \). Archie’s empirical relation:
$$\boxed{F = \frac{a}{\phi^{m}}}$$| Parameter | Name | Typical values |
|---|---|---|
| \( a \) | tortuosity factor | 1 (Archie); 0.62 (Humble formula for sands, with \( m = 2.15 \)); 0.81 (with \( m = 2 \), a common approximation to Humble) |
| \( m \) | cementation exponent | about 1.3 for unconsolidated sands; about 2 for consolidated sandstones and intergranular carbonates; higher (2.5 and above) where porosity is in isolated vugs or moulds; lower (towards 1) where fractures provide straight paths |
| \( n \) | saturation exponent (next section) | about 2 for water-wet rocks; higher in oil-wet rocks |
Because \( F = 1/\phi^m \) with \( a = 1 \) gives \( F = 1 \) at \( \phi = 1 \) (pure water), \( a = 1 \) is the physically consistent choice; \( a \ne 1 \) values are fits over a limited porosity range.
Water Saturation: Archie’s Equation
When hydrocarbons occupy part of the pore space, the rock is more resistive than \( R_o \). The resistivity index \( I \) relates the two:
$$I = \frac{R_t}{R_o} = S_w^{-n}$$Combining with \( F \):
$$\boxed{S_w = \left(\frac{a\,R_w}{\phi^{m}\,R_t}\right)^{1/n} = \left(\frac{F\,R_w}{R_t}\right)^{1/n} = \left(\frac{R_o}{R_t}\right)^{1/n}}$$With \( n = 2 \), a rock reading four times \( R_o \) has \( S_w = 0.5 \); one reading 16 times \( R_o \) has \( S_w = 0.25 \). Hydrocarbon saturation is \( S_h = 1 - S_w \).
Assumptions: clean formation (no conductive clay), the matrix and hydrocarbon are insulators, \( R_t \) is the true uninvaded resistivity, \( R_w \) is at formation temperature, and \( a \), \( m \), \( n \) are appropriate for the rock.
The flushed zone
The same law applies to the flushed zone with filtrate:
$$S_{xo} = \left(\frac{a\,R_{mf}}{\phi^{m}\,R_{xo}}\right)^{1/n}$$\( 1 - S_{xo} \) is the residual hydrocarbon saturation left after invasion. Comparing \( S_w \) and \( S_{xo} \) shows whether the hydrocarbons moved:
- \( S_{xo} \approx S_w \): filtrate did not displace hydrocarbon; hydrocarbons are not moveable (or the zone is water).
- \( S_{xo} \gg S_w \): filtrate pushed hydrocarbons out; they are moveable. The moveable hydrocarbon index \( S_w/S_{xo} \) is well below 1.
- Moveable hydrocarbon volume: \( \phi(S_{xo} - S_w) \).
Ratio method. Dividing the two Archie equations eliminates \( \phi \), \( a \) and \( m \):
$$\frac{R_{xo}}{R_t} = \frac{R_{mf}}{R_w}\left(\frac{S_w}{S_{xo}}\right)^{n}$$It needs no porosity, only \( R_{xo}/R_t \) and \( R_{mf}/R_w \) (which the SP gives directly). An extra empirical assumption about the link between \( S_{xo} \) and \( S_w \) in moderately invaded zones then gives \( S_w \) alone.
Finding Rw
- From a water zone: in a clean zone known to be 100% water, \( R_t = R_o \), so \( R_w = R_o/F = R_o\,\phi^m/a \).
- From the SP: \( \text{SSP} = -K\log(R_{mf}/R_w) \) (see the electrical logs page).
- From produced-water samples or catalogues, corrected to formation temperature.
- \( R_{wa} \) method: compute the apparent water resistivity
at every depth. In water zones \( R_{wa} = R_w \), so the lowest \( R_{wa} \) values in a clean sequence give \( R_w \). Elsewhere \( S_w = (R_w/R_{wa})^{1/n} \): with \( n = 2 \), \( R_{wa} \ge 4R_w \) means \( S_w \le 0.5 \), a quick hydrocarbon flag.
The Pickett plot
Take logarithms of Archie’s equation:
$$\log R_t = -m\,\log\phi + \log(a\,R_w) - n\,\log S_w$$On log–log axes of \( R_t \) (x or y) against \( \phi \), points of constant \( S_w \) lie on straight lines of slope \( -m \) (in the \( \log R_t \) versus \( \log\phi \) sense). The water line (\( S_w = 1 \)) passes through the water-zone points; its slope gives \( m \), and its value at \( \phi = 1 \) gives \( aR_w \). Lines for \( S_w = 0.5, 0.25 \dots \) are parallel, shifted by \( n\log S_w \). Hydrocarbon points plot on the high-resistivity side. The plot solves for \( m \), \( R_w \) and \( S_w \) together without knowing any of them beforehand.
A Hingle plot does the same on linear axes by plotting \( \phi \) against \( R_t^{-1/m} \) (for a chosen \( m \)): water-zone points fall on a straight line through the matrix point.
Bulk volume water
$$\text{BVW} = \phi\,S_w$$is the fraction of the bulk rock occupied by water. In a zone at irreducible water saturation (water held by capillarity, not producible), BVW is nearly constant from level to level: where porosity is higher, \( S_w \) is proportionally lower. Scattered BVW values suggest a transition zone that will produce some water. Finer-grained rocks hold more irreducible water, so the constant value depends on grain size and lithology.
Shaly sands
Clay minerals conduct through exchangeable cations on their surfaces. In a shaly sand this extra conduction lowers \( R_t \), so the clean Archie equation over-estimates \( S_w \): hydrocarbon zones can look wet (“low-resistivity pay”). Shaly-sand models add a clay-conductivity term: the Simandoux and Indonesia equations (using \( V_{sh} \) and \( R_{sh} \)), and the Waxman–Smits and dual-water models (using the cation exchange capacity of the clays). For the exam, know the direction of the error and the names.
Permeability from Logs
Permeability \( k \) is the ability of a rock to transmit fluid (Darcy’s law). Its unit is the darcy: about \( 0.987\times10^{-12} \) m²; reservoir values are usually given in millidarcies (md). Unlike porosity, permeability depends on pore-throat size, not just pore volume, and no conventional log measures it directly.
| Approach | What it uses |
|---|---|
| Qualitative indicators | mud cake on the caliper, microlog positive separation, SP deflection, separation of shallow and deep resistivity (invasion), Stoneley-wave attenuation |
| Empirical porosity–saturation transforms | permeability rises with porosity and falls with irreducible water saturation (finer grains hold more water and have smaller throats). The Timur form, with \( \phi \) and \( S_{wi} \) in percent: \( k\ (\text{md}) = 0.136\,\phi^{4.4}/S_{wi}^{2} \) |
| NMR logs | relaxation-time distribution gives pore sizes, free-fluid and bound-fluid volumes; permeability from Coates or mean-\( T_2 \) (SDR) type transforms calibrated to cores |
| Formation testers | pressure drawdown and build-up at a probe give fluid mobility \( k/\mu \) |
| Core calibration | log porosity related to core permeability by a field-specific regression |
Lithology from Logs
Single logs are ambiguous: a porosity reading depends on both lithology and porosity. Crossplots of two porosity logs separate the two, because each mineral has a different combination of responses.
Two-log crossplots
| Crossplot | What it shows |
|---|---|
| Neutron–density | the most used: lines for sandstone, limestone and dolomite, graduated in porosity; a point between two lines gives a two-mineral mix and its porosity. Gas moves points to the upper left (towards low neutron), shale towards high neutron |
| Sonic–density and sonic–neutron | similar, less sensitive to gas in some cases; sonic misses secondary porosity |
| Pe–density | Pe identifies the mineral almost independently of porosity |
Lithology-independent parameters
M–N plot. Combines all three porosity logs into two quantities that depend mainly on the matrix:
$$M = \frac{\Delta t_f - \Delta t}{\rho_b - \rho_f}\times0.01,\qquad N = \frac{\phi_{Nf} - \phi_N}{\rho_b - \rho_f}$$(\( \Delta t \) in µs/ft, densities in g/cm³, \( \phi_{Nf} = 1 \) for fresh water). Using \( \Delta t_f = 189 \), \( \rho_f = 1.0 \): pure limestone gives \( M = 0.827 \), \( N = 0.585 \); sandstone gives \( M \approx 0.81 \); dolomite \( M \approx 0.78 \). Points fall inside the triangle of the three minerals; gas, shale and secondary porosity shift them in known directions.
Apparent matrix parameters (MID plots). Using porosity from the neutron–density crossplot, compute the matrix value that would explain each reading:
$$\rho_{maa} = \frac{\rho_b - \phi\,\rho_f}{1 - \phi},\qquad \Delta t_{maa} = \frac{\Delta t - \phi\,\Delta t_f}{1 - \phi},\qquad U_{maa} = \frac{\text{Pe}\,\rho_e - \phi\,U_f}{1 - \phi}$$A clean quartz sandstone gives \( \rho_{maa} \approx 2.65 \) and \( U_{maa} \approx 4.8 \); calcite about 2.71 and 13.8; dolomite about 2.87 and 9.0. Anhydrite plots apart on \( \rho_{maa} \).
From Logs to Pay
- Cutoffs. Net reservoir is rock with \( V_{sh} \) below and \( \phi \) above chosen limits; net pay adds an \( S_w \) limit. Cutoffs are field-specific, set from core and test data.
- Hydrocarbon pore thickness: \( \text{HPT} = \sum h\,\phi\,(1 - S_w) \) over net pay. For 20 m of net pay at \( \phi = 0.20 \) and \( S_w = 0.25 \): \( 20 \times 0.20 \times 0.75 = 3.0 \) m of hydrocarbon column.
- Fluid type: gas from neutron–density crossover; oil versus water from resistivity; contacts from changes in \( R_t \) or \( R_{wa} \) in a continuous sand, confirmed by formation-tester pressure gradients.
- Volumes: \( A \times \text{HPT} \) divided by the formation volume factor gives in-place hydrocarbon, as in the STOIIP equation of the petroleum geology page.
Memory Tricks
Don’t Confuse
| Pair | First | Second |
|---|---|---|
| \( R_o \) vs \( R_t \) | resistivity if 100% water-saturated | measured true resistivity, with whatever fluids are present |
| \( F \) vs \( I \) | \( R_o/R_w \): pore geometry | \( R_t/R_o = S_w^{-n} \): saturation |
| \( m \) vs \( n \) | cementation exponent: pore geometry | saturation exponent: wettability |
| \( S_w \) vs \( S_{xo} \) | uninvaded zone, with \( R_t \), \( R_w \) | flushed zone, with \( R_{xo} \), \( R_{mf} \) |
| \( S_{wi} \) vs \( S_w \) | irreducible (immobile) saturation | actual saturation; equal only at irreducible conditions |
| Porosity vs permeability | storage (pore volume) | flow (pore throats) |
| \( R_{wa} \) vs \( R_w \) | computed at every level as \( R_t/F \) | true water resistivity; equals \( R_{wa} \) only in water zones |
| Neutron–density crossplot vs M–N plot | two logs; lithology and porosity together | three logs; lithology largely independent of porosity |
Common Mistakes
Practice
All questions below are original practice questions written for this page. They are not from any CSIR NET paper.
Level 1: Foundation
- Define the formation factor in terms of resistivities.
- Write Archie’s water-saturation equation.
- What does a constant value of \( \phi S_w \) through a reservoir interval suggest?
Answers
- \( F = R_o/R_w \): resistivity of the fully water-saturated rock divided by the resistivity of the water; also \( F = a/\phi^m \).
- \( S_w^{\,n} = aR_w/(\phi^m R_t) \).
- The zone is at irreducible water saturation: it should produce hydrocarbon with little or no water.
Level 2: Part B Style
Practice Q1. A clean sandstone has porosity 0.20, \( R_w = 0.05 \) Ω·m and \( R_t = 20 \) Ω·m. With \( a = 1 \), \( m = n = 2 \), the water saturation is:
(a) 0.0625 (b) 0.11 (c) 0.25 (d) 0.50
Answer: (c) 0.25
\( F = 1/0.20^2 = 25 \); \( R_o = 25 \times 0.05 = 1.25 \) Ω·m; \( S_w = \sqrt{1.25/20} = \sqrt{0.0625} = 0.25 \). (a) forgets the square root. (b) uses \( F = 1/\phi = 5 \), so \( S_w = \sqrt{0.25/20} = 0.11 \). (d) takes the root twice, \( 0.0625^{1/4} = 0.5 \).
Practice Q2. In a clean sand with porosity 0.25 (\( a = 1 \), \( m = 2 \)), \( R_t = 2.0 \) Ω·m. Water zones in the same sand give \( R_w = 0.05 \) Ω·m. The apparent water resistivity and the implied water saturation (\( n = 2 \)) are:
(a) 0.125 Ω·m; 0.63 (b) 0.125 Ω·m; 0.40 (c) 0.50 Ω·m; 0.32 (d) 0.125 Ω·m; 0.16
Answer: (a) 0.125 Ω·m; 0.63
\( F = 16 \), \( R_{wa} = R_t/F = 2.0/16 = 0.125 \) Ω·m. \( S_w = (R_w/R_{wa})^{1/2} = (0.4)^{1/2} = 0.632 \). (b) forgets the root. (c) uses \( F = 1/\phi = 4 \), so \( R_{wa} = 0.5 \) and \( S_w = \sqrt{0.1} = 0.32 \). (d) squares the ratio instead of taking its root.
Practice Q3. On a Pickett plot from a water-bearing sand, one point has \( \phi = 0.10 \), \( R_t = 10 \) Ω·m and another \( \phi = 0.25 \), \( R_t = 1.6 \) Ω·m. With \( a = 1 \), the cementation exponent and \( R_w \) are:
(a) \( m = 2.0 \), \( R_w = 0.10 \) Ω·m (b) \( m = 2.0 \), \( R_w = 1.0 \) Ω·m (c) \( m = 1.5 \), \( R_w = 0.32 \) Ω·m (d) \( m = 2.5 \), \( R_w = 0.03 \) Ω·m
Answer: (a)
Slope: \( m = \log(10/1.6)/\log(0.25/0.10) = 0.796/0.398 = 2.0 \). Then \( R_w = R_o\phi^m = 10 \times 0.01 = 0.10 \) Ω·m (check: \( 1.6 \times 0.0625 = 0.10 \)). (b) multiplies by \( \phi \) instead of \( \phi^m \) (\( 10 \times 0.10 = 1.0 \)). (c) and (d) misread the slope.
Practice Q4. Using the Timur relation \( k = 0.136\,\phi^{4.4}/S_{wi}^2 \) (md; \( \phi \) and \( S_{wi} \) in percent), a sand with 25% porosity and 20% irreducible water has a permeability of about:
(a) 5 md (b) 48 md (c) 480 md (d) 4,800 md
Answer: (c) about 480 md
\( 25^{4.4} = e^{4.4\ln25} = e^{14.163} \approx 1.416\times10^6 \). \( k = 0.136 \times 1.416\times10^6/400 \approx 481 \) md. The other options are powers-of-ten slips; estimate \( 25^{4.4} \) via logarithms (\( 4.4 \times 1.398 = 6.15 \)) to check the order of magnitude.
Level 3: Part C Style
Practice Q5. Three clean sandstone zones in one well (same water) give:
| Zone | GR (API) | \( \rho_b \) (g/cm³) | \( \phi_N \) (sandstone units) | \( R_t \) (Ω·m) |
|---|---|---|---|---|
| A | 30 | 2.25 | 0.09 | 60 |
| B | 32 | 2.32 | 0.21 | 20 |
| C | 30 | 2.32 | 0.20 | 1.25 |
Take \( \rho_{ma} = 2.65 \), \( \rho_f = 1.0 \), \( a = 1 \), \( m = n = 2 \). Zone C is known to be water-bearing. Which interpretation is correct?
(a) A gas with \( S_w \approx 0.16 \); B oil with \( S_w \approx 0.24 \); C water, \( R_w = 0.05 \) Ω·m (b) A oil with \( S_w \approx 0.12 \); B gas with \( S_w \approx 0.24 \); C water, \( R_w = 0.05 \) Ω·m (c) A gas with \( S_w \approx 0.16 \); B water; C water, \( R_w = 0.25 \) Ω·m (d) A shale; B oil with \( S_w \approx 0.50 \); C water, \( R_w = 0.05 \) Ω·m
Answer: (a)
C (water zone): \( \phi_D = (2.65 - 2.32)/1.65 = 0.20 \), agreeing with \( \phi_N = 0.20 \); \( \phi = 0.20 \). \( R_w = R_t\phi^2 = 1.25 \times 0.04 = 0.05 \) Ω·m.
A: \( \phi_D = 0.40/1.65 = 0.242 \) against \( \phi_N = 0.09 \): a large crossover with low GR, so gas. \( \phi = \sqrt{(0.0081 + 0.0588)/2} = \sqrt{0.03344} = 0.183 \). \( S_w = \sqrt{0.05/(0.03344 \times 60)} = \sqrt{0.0249} = 0.158 \).
B: \( \phi_D = 0.20 \), \( \phi_N = 0.21 \): no crossover, liquid. \( \phi \approx 0.205 \). \( S_w = \sqrt{0.05/(0.0420 \times 20)} = \sqrt{0.0595} = 0.244 \): oil.
(b) takes A’s porosity as the density value alone (\( S_w = \sqrt{0.05/(0.242^2 \times 60)} \approx 0.12 \)), misses the gas signature, and calls the liquid zone B gas. (c) misreads C (\( R_w = 1.25 \times 0.20 \) uses \( m = 1 \)). (d) calls A shale despite its low GR.
Practice Q6. A vuggy limestone has porosity 0.15, \( R_w = 0.04 \) Ω·m and \( R_t = 30 \) Ω·m. An analyst uses \( m = 2 \); core measurements later show \( m = 2.5 \) (\( a = 1 \), \( n = 2 \)). Which statement is correct?
(a) \( S_w \) changes from about 0.24 to about 0.39; the original estimate was optimistic (b) \( S_w \) changes from about 0.39 to about 0.24; the original estimate was pessimistic (c) \( S_w \) is unchanged because \( m \) cancels in Archie’s equation (d) \( S_w \) changes from about 0.24 to about 0.32
Answer: (a)
\( m = 2 \): \( \phi^2 = 0.0225 \), \( S_w = \sqrt{0.04/(0.0225 \times 30)} = \sqrt{0.0593} = 0.243 \).
\( m = 2.5 \): \( \phi^{2.5} = 0.008714 \), \( S_w = \sqrt{0.04/(0.008714 \times 30)} = \sqrt{0.153} = 0.391 \).
A higher \( m \) means a higher \( F \), so more of the measured resistivity is explained by pore geometry and less by hydrocarbons: \( S_w \) rises. The \( m = 2 \) answer was optimistic. (c) confuses Archie with the ratio method, where \( m \) cancels. (d) changes the wrong exponent: keeping \( m = 2 \) and setting \( n = 2.5 \) gives \( 0.0593^{0.4} = 0.32 \).
Practice Q7. In a clean sand (\( \phi = 0.20 \), \( a = 1 \), \( m = n = 2 \)): \( R_t = 20 \) Ω·m, \( R_w = 0.05 \) Ω·m, \( R_{xo} = 15 \) Ω·m and \( R_{mf} = 0.50 \) Ω·m. Consider these statements:
- \( S_w = 0.25 \) and \( S_{xo} \approx 0.91 \).
- The moveable hydrocarbon index \( S_w/S_{xo} \approx 0.27 \), indicating moveable hydrocarbons.
- The ratio method gives \( S_w/S_{xo} \) without using porosity, and agrees with statement 2.
- Residual hydrocarbon saturation in the flushed zone is about 0.75.
Which are correct?
(a) 1 and 2 only (b) 1, 2 and 3 only (c) 2, 3 and 4 only (d) all four
Answer: (b) 1, 2 and 3 only
- True. \( S_w = \sqrt{25 \times 0.05/20} = 0.25 \); \( S_{xo} = \sqrt{25 \times 0.50/15} = \sqrt{0.833} = 0.913 \).
- True. \( 0.25/0.913 = 0.274 \): far below 1, so filtrate has displaced most of the hydrocarbon near the hole.
- True. \( (S_w/S_{xo})^2 = (R_{xo}/R_t)/(R_{mf}/R_w) = 0.75/10 = 0.075 \), so \( S_w/S_{xo} = 0.274 \).
- False. Residual hydrocarbon saturation is \( 1 - S_{xo} = 0.087 \), about 0.09. The value 0.75 is the original hydrocarbon saturation \( 1 - S_w \).
Quick Revision Table
| Idea | Fact or formula |
|---|---|
| Formation factor | \( F = R_o/R_w = a/\phi^m \) |
| Constants | \( a = 1 \), \( m = n = 2 \); Humble \( 0.62/\phi^{2.15} \); \( m \approx 1.3 \) unconsolidated, higher for vugs, lower for fractures |
| Resistivity index | \( I = R_t/R_o = S_w^{-n} \) |
| Archie | \( S_w = (aR_w/\phi^m R_t)^{1/n} \) |
| Flushed zone | \( S_{xo} = (aR_{mf}/\phi^m R_{xo})^{1/n} \); residual HC \( = 1 - S_{xo} \) |
| Movability | \( S_w/S_{xo} \ll 1 \): moveable; moveable volume \( \phi(S_{xo} - S_w) \) |
| Ratio method | \( R_{xo}/R_t = (R_{mf}/R_w)(S_w/S_{xo})^n \); no porosity needed |
| \( R_{wa} \) | \( R_t/F \); minimum in clean sequence = \( R_w \); \( S_w = (R_w/R_{wa})^{1/n} \) |
| Pickett | log \( R_t \) vs log \( \phi \): slope \( -m \), water line through \( aR_w \) at \( \phi = 1 \) |
| BVW | \( \phi S_w \); constant at irreducible saturation |
| Shaly sand | clay conduction lowers \( R_t \); clean Archie over-estimates \( S_w \); Simandoux, Indonesia, Waxman–Smits, dual water |
| Permeability | not measured directly; Timur \( k = 0.136\phi^{4.4}/S_{wi}^2 \); NMR; testers; 1 D ≈ \( 0.987\times10^{-12} \) m² |
| M–N | \( M = 0.01(\Delta t_f - \Delta t)/(\rho_b - \rho_f) \); \( N = (\phi_{Nf} - \phi_N)/(\rho_b - \rho_f) \); limestone 0.827, 0.585 |
| Apparent matrix | \( \rho_{maa} = (\rho_b - \phi\rho_f)/(1 - \phi) \); \( U_{maa} \): quartz 4.8, dolomite 9.0, calcite 13.8 |
| Pay | cutoffs on \( V_{sh} \), \( \phi \), \( S_w \); HPT \( = \sum h\phi(1 - S_w) \) |
Key Takeaways
What’s Next
- Well Logging: Quick Revision: every formula, value and trap from the chapter on one page.
- Logging Operations: Open-Hole, Cased-Hole, Production Logging and LWD: how saturation is monitored behind casing once the well produces.
- Gas Hydrates, Coal-Bed Methane, Nuclear and Non-Conventional Energy: unconventional reservoirs where these standard interpretations need modification.
- Well Logging: back to the chapter overview.