Free Electron Theory, Drude Model, Hall Effect and Thermoelectric Power
CSIR NET Part C: Drude conductivity, plasma frequency, Sommerfeld model, Wiedemann–Franz law, Hall coefficient, two-carrier Hall effect, Seebeck coefficient.
- 17 min
On this page · 13 sections
Prerequisites
- Classical and Quantum Statistics: Ideal Bose and Fermi Gases: Fermi energy, density of states and the Sommerfeld heat capacity. This page applies them to transport.
- Charged Particles in Uniform Fields: Lorentz force and cyclotron motion, which drive the Hall effect.
- EM Waves: Reflection, Refraction and Polarization: wave propagation in a conductor, behind the plasma frequency.
- Bonding, Elastic Properties, Phonons and Lattice Specific Heat: phonons, the main scatterers of electrons at room temperature.
The Hook: A Model That Was Right for the Wrong Reasons
The Drude Model
Assumptions
- Between collisions, electrons move freely (no electron–ion or electron–electron forces except at collisions).
- Collisions are instantaneous and randomise the velocity.
- The probability of a collision in time \( dt \) is \( dt/\tau \); \( \tau \) is the relaxation time.
- Electrons reach thermal equilibrium only through collisions.
The mean momentum then obeys
$$\frac{d\mathbf{p}}{dt} = -\frac{\mathbf{p}}{\tau} - e(\mathbf{E} + \mathbf{v}\times\mathbf{B})$$DC conductivity and mobility
In a steady field, \( \mathbf{p} = -e\tau\mathbf{E} \), the drift velocity is \( \mathbf{v}_d = -e\tau\mathbf{E}/m \) and \( \mathbf{J} = -ne\mathbf{v}_d \):
$$\boxed{\sigma = \frac{ne^2\tau}{m}, \qquad \mu = \frac{e\tau}{m}, \qquad \sigma = ne\mu}$$Matthiessen’s rule. Independent scattering mechanisms add rates: \( 1/\tau = 1/\tau_{\text{phonon}} + 1/\tau_{\text{impurity}} \), so \( \rho(T) = \rho_0 + \rho_{\text{ph}}(T) \). The residual resistivity \( \rho_0 \) (impurities, defects) is temperature-independent; the phonon part is linear in \( T \) at high temperature and falls steeply (Bloch–Grüneisen \( T^5 \)) well below \( \theta_D \).
AC conductivity and the plasma frequency
For \( \mathbf{E}(t) = \mathbf{E}_0e^{-i\omega t} \):
$$\sigma(\omega) = \frac{\sigma_0}{1 - i\omega\tau}$$Putting this into Maxwell’s equations gives a dielectric function
$$\varepsilon(\omega) = 1 - \frac{\omega_p^2}{\omega^2} \quad (\omega\tau \gg 1), \qquad \boxed{\omega_p^2 = \frac{ne^2}{\varepsilon_0m}}$$- \( \omega < \omega_p \): \( \varepsilon < 0 \), waves are evanescent, the metal reflects.
- \( \omega > \omega_p \): \( \varepsilon > 0 \), the metal becomes transparent. Alkali metals are transparent in the ultraviolet.
- \( \omega_p \) is also the frequency of collective longitudinal oscillations of the electron gas; the quantum \( \hbar\omega_p \) is the plasmon.
For \( n = 2.65\times10^{28} \) m\( ^{-3} \), \( \omega_p = 9.2\times10^{15} \) s\( ^{-1} \), \( \lambda_p = 2\pi c/\omega_p \approx 205 \) nm, \( \hbar\omega_p \approx 6.0 \) eV.
Thermal conductivity and Wiedemann–Franz
Kinetic theory gives \( \kappa = \tfrac13c_vv^2\tau \) (\( c_v \) per volume). Dividing by \( \sigma \):
$$\frac{\kappa}{\sigma T} = L$$| Model | \( c_v \) per electron | \( v^2 \) | \( L \) |
|---|---|---|---|
| Drude (classical) | \( \tfrac32k_B \) | \( 3k_BT/m \) | \( \tfrac32(k_B/e)^2 = 1.11\times10^{-8} \) W Ω K\( ^{-2} \) |
| Sommerfeld (quantum) | \( \tfrac{\pi^2}{2}k_B\,T/T_F \) (about 100 times smaller) | \( v_F^2 \) (about 100 times larger) | \( \boxed{\tfrac{\pi^2}{3}(k_B/e)^2 = 2.44\times10^{-8}} \) W Ω K\( ^{-2} \) |
The classical errors in \( c_v \) and \( v^2 \) cancel; Drude’s own paper also had a stray factor of 2 that brought his number closer to experiment. The law holds when the same elastic scattering limits both currents: at room temperature and at the lowest temperatures (impurity scattering), but not at intermediate temperatures where small-angle phonon scattering degrades the heat current more than the charge current.
The Sommerfeld Free-Electron Model
Free electrons in a box, filling plane-wave states up to \( E_F \) with two spins:
| Quantity | Formula | Typical metal |
|---|---|---|
| Fermi wavevector | \( k_F = (3\pi^2n)^{1/3} \) | about \( 10^{10} \) m\( ^{-1} \) |
| Fermi energy | \( E_F = \hbar^2k_F^2/2m \) | 2–12 eV |
| Fermi velocity | \( v_F = \hbar k_F/m \) | about \( 10^6 \) m s\( ^{-1} \) |
| Fermi temperature | \( T_F = E_F/k_B \) | \( 10^4 \)–\( 10^5 \) K |
| Density of states at \( E_F \) | \( g(E_F) = 3n/2E_F \) (per volume) | |
| Electronic heat capacity | \( C_{\text{el}} = \tfrac{\pi^2}{3}g(E_F)k_B^2T = \gamma T \) | \( \gamma \sim 1 \) mJ mol\( ^{-1} \) K\( ^{-2} \) |
| Pauli susceptibility | \( \chi_P = \mu_0\mu_B^2g(E_F) \), temperature-independent |
For \( n = 8.5\times10^{28} \) m\( ^{-3} \): \( k_F = 1.36\times10^{10} \) m\( ^{-1} \), \( E_F = 7.05 \) eV, \( T_F = 8.2\times10^4 \) K, and for one electron per atom \( \gamma = \tfrac{\pi^2}{2}R/T_F \approx 0.50 \) mJ mol\( ^{-1} \) K\( ^{-2} \). Measured \( \gamma \) values differ from the free-electron estimate; the ratio defines a thermal effective mass \( m^*/m = \gamma_{\text{obs}}/\gamma_{\text{free}} \).
Successes and failures
| Free-electron model explains | It does not explain |
|---|---|
| Ohm’s law, \( \sigma = ne^2\tau/m \) | Why some elements are insulators or semiconductors |
| Wiedemann–Franz law (with correct \( L \)) | Positive Hall coefficients in some metals |
| \( C_{\text{el}} \propto T \), small | Magnetoresistance (zero in the one-carrier model) |
| Pauli paramagnetism, weak and \( T \)-independent | The relation between valence and conduction (Be, Al vs Na) |
| UV transparency of alkali metals | The temperature dependence of \( \tau \) from first principles |
The Hall Effect
One type of carrier
Current density \( J_x \) flows along \( x \) in a field \( B_z \). The Lorentz force deflects carriers along \( y \) until a transverse Hall field \( E_y \) cancels it. In steady state (\( J_y = 0 \)):
$$E_y = R_HJ_xB_z, \qquad \boxed{R_H = -\frac{1}{ne}\ \text{(electrons)}, \quad R_H = +\frac{1}{pe}\ \text{(holes)}}$$For a slab of thickness \( t \) (along \( B \)) carrying current \( I \): \( V_H = R_HIB/t \). Remarkably, \( R_H \) does not depend on \( \tau \). The Hall angle between \( \mathbf{E} \) and \( \mathbf{J} \) is \( \tan\theta_H = \omega_c\tau = \mu B \), with \( \omega_c = eB/m \). Combined with \( \sigma \), the Hall coefficient gives the Hall mobility \( \mu_H = |R_H|\sigma \).
The Hall voltage is much larger in semiconductors (\( n \) small) than in metals, which is why Hall probes use semiconductors.
Two types of carrier
With electrons (\( n, \mu_e \)) and holes (\( p, \mu_h \)), in weak fields:
$$\boxed{R_H = \frac{p\mu_h^2 - n\mu_e^2}{e(p\mu_h + n\mu_e)^2}}$$- The sign depends on \( p\mu_h^2 \) versus \( n\mu_e^2 \), not on \( p \) versus \( n \). An intrinsic semiconductor (\( n = p \)) has negative \( R_H \) if \( \mu_e > \mu_h \).
- \( R_H \) can change sign with temperature in a \( p \)-type semiconductor: holes dominate at low \( T \), intrinsic electrons with higher mobility take over at high \( T \).
- With two carrier types the transverse forces cannot be balanced for both, so the longitudinal resistance increases with \( B \): magnetoresistance, absent in the one-carrier Drude model.
Thermoelectric Power
The Seebeck effect
A temperature gradient across an open-circuited conductor produces an electric field: \( \mathbf{E} = S\nabla T \), where \( S \) (also written \( Q \)) is the Seebeck coefficient or thermopower. Hot carriers diffuse to the cold end until a field stops them. The sign of \( S \) gives the sign of the carriers: negative for electrons, positive for holes.
| Model | \( S \) | Size at 300 K |
|---|---|---|
| Drude, classical (\( S = -c_v/3ne \)) | \( -\dfrac{k_B}{2e} \) | \( -43 \) μV K\( ^{-1} \), temperature independent |
| Same estimate with Sommerfeld \( c_v \) | \( -\dfrac{\pi^2}{6}\dfrac{k_B}{e}\dfrac{k_BT}{E_F} \) | about \( -0.5 \) μV K\( ^{-1} \) for \( E_F = 7 \) eV |
| Mott formula (general degenerate conductor) | \( -\dfrac{\pi^2k_B^2T}{3e}\left.\dfrac{d\ln\sigma(E)}{dE}\right\vert _{E_F} \) | a few μV K\( ^{-1} \), linear in \( T \) |
| Non-degenerate semiconductor | \( \approx \mp\dfrac{k_B}{e}\left(\dfrac{\vert E_c - \mu\vert }{k_BT} + \text{const}\right) \) | hundreds of μV K\( ^{-1} \) |
The prefactor in the metallic case depends on how \( \tau \) varies with energy (with an energy-independent \( \tau \) and \( \sigma(E) \propto E^{3/2} \), the Mott formula gives \( \pi^2/2 \) instead of \( \pi^2/6 \)), but the physics is fixed: in a metal \( S \sim (k_B/e)(k_BT/E_F) \), small and linear in \( T \), because only electrons within \( k_BT \) of \( E_F \) carry entropy. In a semiconductor each carrier carries an energy of order \( E_c - \mu \gg k_BT \), so \( S \) is hundreds of times larger: why practical thermoelectric devices use doped semiconductors.
Peltier and Thomson effects
| Effect | Statement | Relation |
|---|---|---|
| Seebeck | open-circuit emf in a two-metal loop with junctions at \( T_1, T_2 \): \( \mathcal{E} = \int_{T_1}^{T_2}(S_A - S_B)\,dT \) | |
| Peltier | heat \( \Pi I \) absorbed or released at a junction when current \( I \) flows | Kelvin: \( \Pi = ST \) |
| Thomson | heat per unit current per unit gradient along one conductor | \( \mu_T = T\,dS/dT \) |
The thermoelectric figure of merit \( ZT = S^2\sigma T/\kappa \) shows the trade-off: large \( S \) and \( \sigma \), small \( \kappa \).
Memory Tricks
- “Sigma is n-e-squared-tau-over-m.” Mobility drops one \( e \) and the \( n \): \( \mu = e\tau/m \).
- Lorenz numbers: “1.1 classical, 2.44 quantum”, both \( \times10^{-8} \) W Ω K\( ^{-2} \).
- Hall sign = carrier sign. Electrons negative, holes positive; with two carriers, the one with the larger \( n\mu^2 \) wins.
- Below \( \omega_p \) mirror, above \( \omega_p \) window.
- Thermopower: metals micro, semiconductors hundreds of micro (volts per kelvin).
Don’t Confuse
| This | vs | That |
|---|---|---|
| Drift velocity \( v_d \sim 10^{-4} \) m s\( ^{-1} \) | Fermi velocity \( v_F \sim 10^6 \) m s\( ^{-1} \) (sets \( \ell = v_F\tau \)) | |
| Relaxation time \( \tau \) (from \( \sigma \)) | Hall coefficient \( R_H \) (independent of \( \tau \)) | |
| Plasma frequency \( \sqrt{ne^2/\varepsilon_0m} \) | Cyclotron frequency \( eB/m \) | |
| Peltier coefficient \( \Pi \) (V) | Seebeck coefficient \( S \) (V K\( ^{-1} \)); \( \Pi = ST \) | |
| Pauli susceptibility: \( T \)-independent | Curie susceptibility of local moments: \( \propto 1/T \) | |
| Two-carrier sign: compare \( p\mu_h^2 \) with \( n\mu_e^2 \) | One-carrier: just the carrier charge |
Common Mistakes
Practice
All questions below are original practice questions written for this page. They are not from any CSIR NET paper. Use \( e = 1.602\times10^{-19} \) C, \( m_e = 9.11\times10^{-31} \) kg, \( \varepsilon_0 = 8.854\times10^{-12} \) F m\( ^{-1} \), \( k_B = 1.381\times10^{-23} \) J K\( ^{-1} \).
Level 1: Foundation
- Write the Drude conductivity in terms of \( n \), \( e \), \( \tau \) and \( m \).
- What is the sign of the Hall coefficient of an \( n \)-type semiconductor?
- State the Kelvin relation between the Peltier and Seebeck coefficients.
Answers
- \( \sigma = ne^2\tau/m \).
- Negative, \( R_H = -1/(ne) \).
- \( \Pi = ST \).
Level 2: Part B Style
Practice Q1. A metal has a free-electron density of \( 2.65\times10^{28} \) m\( ^{-3} \). Ignoring core polarisation, it becomes transparent for wavelengths shorter than about:
(a) 115 nm (b) 205 nm (c) 410 nm (d) 650 nm
Answer: (b) 205 nm
\( \omega_p = \sqrt{ne^2/\varepsilon_0m} = 9.18\times10^{15} \) s\( ^{-1} \); \( \lambda_p = 2\pi c/\omega_p = 205 \) nm. (a) is the value for \( n = 8.5\times10^{28} \) m\( ^{-3} \).
Practice Q2. A semiconductor slab 0.5 mm thick (along \( \mathbf{B} \)) has \( 1.0\times10^{21} \) electrons m\( ^{-3} \). With a current of 1.0 mA and \( B = 0.50 \) T, the magnitude of the Hall voltage is closest to:
(a) 0.62 mV (b) 3.1 mV (c) 6.2 mV (d) 62 mV
Answer: (c) 6.2 mV
\( V_H = IB/(net) = (10^{-3}\times0.5)/(10^{21}\times1.602\times10^{-19}\times5\times10^{-4}) = 6.24\times10^{-3} \) V.
Practice Q3. In a semiconductor the electron and hole concentrations are equal and \( \mu_e = 3\mu_h \). Its Hall coefficient is:
(a) \( -1/(ne) \) (b) \( -1/(2ne) \) (c) 0 (d) \( +1/(2ne) \)
Answer: (b) −1/(2ne)
\( R_H = \dfrac{n\mu_h^2 - n(3\mu_h)^2}{e(n\mu_h + 3n\mu_h)^2} = \dfrac{-8n\mu_h^2}{16en^2\mu_h^2} = -\dfrac{1}{2ne} \). (c) is the “equal numbers cancel” trap.
Practice Q4. For free electrons obeying Fermi–Dirac statistics with elastic scattering, the Lorenz number \( \kappa/(\sigma T) \) is:
(a) \( \tfrac32(k_B/e)^2 \) (b) \( 3(k_B/e)^2 \) (c) \( \tfrac{\pi^2}{3}(k_B/e)^2 \) (d) \( \tfrac{\pi^2}{2}(k_B/e)^2 \)
Answer: (c)
\( \kappa = \tfrac13c_vv_F^2\tau \) with \( c_v = \tfrac{\pi^2}{2}nk_B^2T/E_F \), and \( \sigma = ne^2\tau/m \); using \( E_F = \tfrac12mv_F^2 \), \( \kappa/\sigma T = \tfrac{\pi^2}{3}(k_B/e)^2 = 2.44\times10^{-8} \) W Ω K\( ^{-2} \). (a) is Drude’s classical value.
Level 3: Part C Style
Practice Q5. A rectangular semiconductor bar has length 5.0 mm (along the current), width 2.0 mm and thickness 0.20 mm (along \( \mathbf{B} \)). With \( I = 2.0 \) mA along the length, the voltage between the ends is 0.25 V. With \( B = 0.40 \) T applied, a Hall voltage of magnitude 5.0 mV appears, with the sign corresponding to positive carriers. Assume one type of carrier. Consider:
- The carrier density is about \( 5.0\times10^{21} \) m\( ^{-3} \).
- The resistivity is 0.010 Ω m.
- The carrier mobility is about 0.125 m\( ^2 \) V\( ^{-1} \) s\( ^{-1} \).
- The Hall angle is about \( 30^\circ \).
Which are correct?
(a) 1 and 2 only (b) 1, 2 and 3 only (c) 2, 3 and 4 only (d) 1, 2, 3 and 4
Answer: (b) 1, 2 and 3 only
- \( p = IB/(eV_Ht) = (2\times10^{-3}\times0.4)/(1.602\times10^{-19}\times5\times10^{-3}\times2\times10^{-4}) = 4.99\times10^{21} \) m\( ^{-3} \). True.
- \( R = 0.25/0.002 = 125 \) Ω; \( \rho = RA/L = 125\times(2\times10^{-3}\times2\times10^{-4})/(5\times10^{-3}) = 0.010 \) Ω m. True.
- \( \mu = 1/(\rho pe) = 1/(0.010\times4.99\times10^{21}\times1.602\times10^{-19}) = 0.125 \) m\( ^2 \) V\( ^{-1} \) s\( ^{-1} \). True.
- \( \tan\theta_H = \mu B = 0.050 \), \( \theta_H \approx 2.9^\circ \). False.
Practice Q6. A monovalent metal has \( n = 8.5\times10^{28} \) m\( ^{-3} \) and resistivity \( 1.7\times10^{-8} \) Ω m at 300 K. Treat its electrons as free. Consider:
- The relaxation time is about \( 2.5\times10^{-14} \) s.
- The Fermi velocity is about \( 1.6\times10^6 \) m s\( ^{-1} \).
- The mean free path is about 39 nm.
- The drift velocity at a current density of \( 10^6 \) A m\( ^{-2} \) is about 1 mm s\( ^{-1} \).
Which are correct?
(a) 1, 2 and 3 only (b) 1 and 2 only (c) 2, 3 and 4 only (d) 1, 2, 3 and 4
Answer: (a) 1, 2 and 3 only
- \( \tau = m/(ne^2\rho) = 2.46\times10^{-14} \) s. True.
- \( v_F = \hbar(3\pi^2n)^{1/3}/m = 1.57\times10^6 \) m s\( ^{-1} \). True.
- \( \ell = v_F\tau = 38.7 \) nm. True.
- \( v_d = J/(ne) = 7.3\times10^{-5} \) m s\( ^{-1} \), about 0.07 mm s\( ^{-1} \). False.
Practice Q7. A lightly doped \( p \)-type semiconductor has \( \mu_e/\mu_h = 4 \). Its Hall coefficient is measured from 100 K to 600 K; at 600 K the sample is intrinsic. Consider:
- At 100 K the Hall coefficient is positive.
- At 600 K the Hall coefficient is negative.
- The Hall coefficient passes through zero at the temperature where \( p = n \).
- At the zero crossing, \( p/n = 16 \).
Which are correct?
(a) 1 and 2 only (b) 1, 2 and 4 only (c) 1, 3 and 4 only (d) 2 and 3 only
Answer: (b) 1, 2 and 4 only
- At low \( T \) holes from acceptors dominate: \( R_H > 0 \). True.
- Intrinsic, \( n \approx p \): \( R_H \propto p\mu_h^2 - n\mu_e^2 = n\mu_h^2(1 - 16) < 0 \). True.
- Zero when \( p\mu_h^2 = n\mu_e^2 \), i.e. \( p/n = (\mu_e/\mu_h)^2 \), not \( p = n \). False.
- \( p/n = 4^2 = 16 \). True.
Quick Revision Table
| Idea | Formula or fact |
|---|---|
| Drude | \( \sigma = ne^2\tau/m \), \( \mu = e\tau/m \), \( v_d = J/ne \) |
| AC | \( \sigma(\omega) = \sigma_0/(1 - i\omega\tau) \) |
| Plasma frequency | \( \omega_p^2 = ne^2/\varepsilon_0m \); transparent for \( \omega > \omega_p \) |
| Free-electron Fermi gas | \( k_F = (3\pi^2n)^{1/3} \); \( g(E_F) = 3n/2E_F \); \( C = \gamma T \) |
| Mean free path | \( \ell = v_F\tau \) |
| Wiedemann–Franz | \( L = \tfrac{\pi^2}{3}(k_B/e)^2 = 2.44\times10^{-8} \) W Ω K\( ^{-2} \) |
| Hall (one carrier) | \( R_H = \mp1/(ne) \); \( V_H = R_HIB/t \); \( \tan\theta_H = \mu B \) |
| Hall (two carriers) | \( R_H = (p\mu_h^2 - n\mu_e^2)/[e(p\mu_h + n\mu_e)^2] \) |
| Seebeck | metals \( \sim(k_B/e)(k_BT/E_F) \), few μV K\( ^{-1} \); classical \( k_B/2e = 43 \) μV K\( ^{-1} \) |
| Kelvin relations | \( \Pi = ST \); \( \mu_T = T\,dS/dT \) |
Key Takeaways
What’s Next
- Band Theory: Metals, Insulators and Semiconductors: the periodic potential, holes, effective mass and why some solids do not conduct.
- Semiconductor Devices: Junctions and Transistors, where Hall measurements and carrier mobilities are used in devices.
- Band Structure of Solids in Chemical Sciences, for the qualitative band picture.
- Condensed Matter Physics: Quick Revision.